Removing the pedal arm from a bike

Some features

Since the system is constantly exposed to the environment against a background of severe mechanical stress, torsional problems can arise. In this case, two methods are used:

  • Soaking the bike pedal in kerosene or thinner to remove as much dirt as possible that is blocking rotation.
  • Heating of the connecting rod and axle. Slight deformation helps loosen the threads and remove the axle.

It is also important to carefully tighten the axle during installation so as not to damage the threads, which is a considerable problem in case of subsequent removal.

Removing the pedals

After preparation, you can proceed with the removal process. For conventional mechanisms, it looks like this:

  • We move the system to the working side. in the direction of the steering wheel.
  • We try to carefully unscrew the pedals from the connecting rod.
  • Remove the plug at the end of the platform, open the lock nut.
  • Unscrew the lock nut, holding the axle at the connecting rod with the second key.
  • Remove the washer (also at the end).
  • Unscrew the cone.
  • We remove the platform from the axle, holding the bearings (it is better to remove them separately, if they are bulk, then put a rag or sheet so that they do not roll far).
  • Pedal removed and disassembled!

removing, pedal, bike

It is important not to forget that the left and right pedals are unscrewed from the connecting rod in their direction: on the right axis. the right thread, on the left. the left.

The contact devices are a little more difficult to disassemble, but they will not cause any problems. when twisting and disassembling, a puller is used, which should hold the axis with a small contact pad.

Required tools and materials

Before removing the pedals, it is necessary to prepare the tool and auxiliary materials that are most likely to be needed.

  • lubrication. it is recommended to clean and lubricate the removed parts;
  • cleaning rags;
  • kerosene or solvent. in case the axles do not unscrew or there are large contaminated areas.
  • an adjustable wrench is a universal solution, a small one is desirable, otherwise it will be difficult to get to the nut;
  • open-end wrench for 15. fits almost all models;
  • bicycle kit. in case of emergency;
  • pedal wrench. supplied by manufacturers for non-standard nuts and just in sets;
  • puller. addition to the foot pedals. a standard tool, often supplied by the manufacturer, serves to hold the axle when turning to the side with a wrench.

How To Remove Bike Crank Arms (Two Types!)

Pedal design

They are not all the same and you need to know a little about their construction. So, the pedal is part of a system that includes a set of sprockets, a crank carriage and, in fact, a set of axles, platforms, bearings and accessories. on this below.

Remove Cranks Without A Crank Puller

Structurally, a bicycle pedal consists of several parts:

  • The axle is a metal pin that is screwed into the connecting rod. Provides the basis for the rest of the structure.
  • Platform. a plane that contacts the foot and is fixed on the axis.
  • Bearings. the assembly that connects the axle and platform, allowing rotation.
  • Fittings. bolts and nuts that fix all the components of the pedal. Unscrewed during disassembly.

On the platform, the pedals are divided into contact (with fastening for special shoes) and ordinary. The method of removal depends on the type: for contact mechanisms, the fastening scheme is slightly more complicated. Combined options, combining, on the one hand, an ordinary platform, and on the other, a contact device, are no different in terms of dismantling from contact.

How to unscrew the pedals on a bike?

The pedal is a simple part, but due to some mounting features and a very long service life, not every cyclist is able to remove them from their bike on their own. Why remove the pedals?

  • Change them after damage.
  • Pedal lubrication.
  • Connecting rod repair or replacement.

First, let’s look at how they are arranged, what types are there, what features should be considered, what tools to prepare before work.

Removing the pedals from the bike is easy enough, but don’t forget about preparing tools and materials, as well as possible problems. The main thing is to keep the entire system in order, since in case of damage or other problems, the inconvenience of using the bike will be very great.

Removing the pedal from the bike: step by step instructions

So, let’s look at the main steps on how to remove a pedal from a bicycle without a puller:

  • Using a screwdriver, remove the plug from the end of the part.
  • We unscrew the platform from the connecting rod using an adjustable wrench. Right pedal counterclockwise, left pedal clockwise.
  • We unscrew the control nut. At the same time, we hold the connecting rod axis with the second key.
  • Remove the washer, which is located at the end of the pedal.
  • We remove the platform from the axle and at the same time hold the bearings. Dismantling ready.

With clipless pedals, the circuit is a little more complicated. Therefore, before removing the pedal from the bike, you must have a special device. The connecting rod has a thread into which the puller is screwed in and begins to squeeze the connecting rod from the axis. At the end of the work, we put the pedal in place, check the strength of the part, and install the plug.

How to remove the pedal from the bike and replace the connecting rod

The pedal is a simple part, but the long life can cause some disassembly problems. Therefore, many experts recommend systematic maintenance of the vehicle, despite the fact that many do not attach importance to this issue.

Let us analyze in which cases it is necessary to remove the pedals:

  • the part is damaged and requires replacement;
  • lubricate the elements;
  • replacement or repair of the connecting rod;
  • you need to understand the features of the system and understand how it works.
READ  Mount for a bike on a car which is better

Before removing the pedal from the bike, the following tools should be prepared:

  • open-end wrench 15;
  • adjustable wrench;
  • if there is a non-standard solution of the manufacturer in the fastening elements, then usually the set contains a key for removing the pedal.

Pedal design

All pedals, despite their different features, have a common design:

  • Platform. the surface on which the foot rests, which is fixed on the axis.
  • Metal axis. a pin made of metal. Has a thread and is screwed into the connecting rod.
  • Bearings. provide torque. Serves as a connecting element between the axle and the platform. There are simple bulk and cartridge bearings that differ in weight and quality.
  • Bolts, nuts.

It should be noted that the design of the pedals is not as simple as it seems at first glance. Therefore, before tackling such problems, for example, how to remove the axle of a bicycle pedal, you should carefully study the overall design.

Bicycle “Stealth

The manufacturer attracts with serious equipment and carbon frames (StelsNavigator 890DCarbon). An amazing aspect is the attractive price-performance ratio.

How to remove pedals from a bike without a puller?

Bicycles are the most popular and convenient form of transport. For some, this is recreation, sports and a great way to attract attention, for example, while performing original stunts on a two-wheeled bike. However, do not forget about timely maintenance and repair. That is why many cycling enthusiasts are faced with the problem of how to remove the pedal from the bike. Having penetrated into the structure of transport, you can easily learn how to carry out repairs yourself. Thus, it will be possible to avoid various unforeseen breakdowns.

Pedal types

  • regular (platform);
  • contact;
  • combined.

Each of the pedal types has its own specifics: the first is created for any footwear, the contact type exists for grip with sports shoes and the universal third type, which has a platform on one side and a clutch mechanism on the other. The method of disassembly also depends on the type of part. The mechanism of conventional pedals is simpler and faster to disassemble.

Pedal Features

Constant mechanical stress on the pedal can cause rotational problems. To quickly deal with them, it is necessary to heat the connecting rod and axle. As a result, the process of metal deformation will take place. This will help to easily remove the axle.

To prolong the life of the pedal, use a chain treatment agent. Thanks to the solvent, stubborn dirt such as bolts can be removed. We use a solvent and a rag (napkin). In this case, the solvent can be replaced with kerosene. You should also not forget about the toxicity of these funds.

Step-by-step instructions on how to remove a pedal from a bike without a puller

After finishing the preparatory work, we proceed to dismantling:

  • First of all, slide the system towards the steering wheel, this position is considered to be working.
  • Gently unscrew the pedals from the crank with an adjustable wrench. Which way to unscrew the pedals on the bike? Right. counterclockwise, left. in the direction.
  • Remove the end cap to expose the locknut. Use a small flat-blade screwdriver to do this.
  • Smoothly unscrew the nut, holding the axle with the second key.
  • Also, a washer remains at the end, which must be removed.
  • At this point, unscrew the cone.
  • It remains to remove the platform from the axle, try to control the position of the bearings in order to exclude their sudden fall.

Difficulties during dismantling arise due to external factors or under heavy loads. There are two options for solving these problems:

  • treat the elements with kerosene or solvent. After soaking in such liquids, dirt that hinders rotation can be easily removed;
  • you can heat the axle and connecting rod, there will be a slight deformation of the metal, and the axle can be easily removed along the thread.

In general, the process of removing the pedals is quite simple, it is much more important to prepare the necessary tools and materials, as well as follow the instructions. It is recommended to return the parts to their place first by hand, and only at the end to tighten with special wrenches.

Required set of tools and materials

Before figuring out how to remove the pedals from the bike, you need to collect all the available tools that will be needed during these works.

Interesting! These tools should always be at hand by the cyclist so that he can make repairs on his own. It is worth buying them at the stage of choosing a bicycle for a man or a woman.

List of materials that you may need:

  • A small adjustable wrench that allows you to unscrew the nuts even in hard-to-reach places.
  • Universal open-end 15th wrench, it fits most models.
  • Dedicated pedal wrench to unscrew custom nuts. Manufacturers attach it to kits, but you can find such a tool in the standard set.
  • If your bike has clip-on pedals, then a puller can come in handy. This tool is used to hold the axle in a fixed position while turning the key.
  • There are special bike kits that are used as a last resort.

In addition to the above things, for removing the pedals, it will come in handy:

  • lubricating fluid. all dismantled parts must be cleaned and lubricated to improve performance and extend service life (you can use the same agent as for processing the chain);
  • rags. used to cleanse all elements;
  • Thinner. Use when there are large dirty areas or problems with loosening elements. Its analogue is kerosene.

A special stand that fixes the vehicle in the air will help to facilitate the process of removing the bike pedals. However, some cyclists argue that this way, they have to put in more physical effort.

How to remove pedals from a bike: sequence of actions

At first glance, the design of the pedal looks simple, but in order to dismantle it, you need to have certain knowledge and a set of tools.

READ  Knocking on the motor wheel of an electric bike reasons

Removing your bike pedals may be necessary for various reasons: before transporting your bike, for regular maintenance checks, or after storing it on your balcony before the season starts. There are situations when a part crunches or emits other atypical sounds, in which case it must either be cleaned or completely dismantled, replaced with a new one. Pedal assemblies of new vehicles often need additional adjustments for a specific person. Therefore, many have the question of how to unscrew the pedals on a bicycle.

Pedal device

Before removing the pedals, first you need to familiarize yourself with the structure of this unit. These steps must be performed before any such repair operations. The pedal consists of several elements, and each model can have a different design, namely:

  • the axle is a special metal pin that is screwed into the connecting rod. She is the base for the rest of the details;
  • platform. a flat surface in direct contact with the sole and located at the end of the axis;
  • bearings. the elements necessary to connect the previous parts into a single mechanism, it is they that allow the platforms to rotate;
  • accessories. a variety of bolts and nuts that hold all the components of the pedal together. When disassembling, the fasteners are unscrewed with special tools.

Depending on the platform, pedals are divided into two groups: contact pedals, in which it is assumed that there is a special mount for cycling shoes, and standard models.

Removal of simple devices does not require much effort, and contact mechanisms with more complex latches are not easy to dismantle.

See how to properly unscrew the pedals on your bike. The video will show the whole process in detail.

How to put the pedals back in place?

Before installing the pedals, it is worth first cleaning the threads on the contact connections of the connecting rods and platforms from dirt. Then just take the right pedal and turn it clockwise. Screwing in should first be done by hand and then using a wrench. Finally, the pedal must be firmly tightened.

A similar operation is performed with the left platform and connecting rod. Only the rotation should be in the opposite direction. Finally, it is worth tightening and securely fixing the pedals once again with a hand wrench, which will exclude their arbitrary unscrewing while driving.

Pedal design

This part is a system element that consists of a set of stars, a pair of connecting rods, a carriage, an axle, bearings, a support platform and fittings. To better understand how to remove pedals from a bike, let’s look at each part separately.

  • The axle is a metal pin built into the connecting rod. Acts as a base on which the rest of the structure is held.
  • A connecting rod is a part that, on one side, is connected to the axle, and on the other, to a freely rotating platform.
  • Bearing assembly. design that ensures smooth running of the system.
  • Platform. a node that acts as a support for the foot during movement and is connected to the axle by means of a connecting rod.
  • Fittings. metal fasteners for fixing all the components of the pedal unit. Completely dismantled during disassembly.

According to the nature of the support platform, there are standard and contact pedals for a bicycle with a mount. The former provide traction with the cyclist’s sole due to the textured surface. The latter contain notches that connect to the corresponding protrusions on special shoes.

There is also a combination pedal option. The latter contain on one side of the platform a regular site, and on the other. a contact.

How to remove pedals from a bike?

First you need to equip yourself with a bicycle wrench long enough to create a suitable lever. The tool is placed in a position parallel to the connecting rod. The key turns in the desired direction (for the right pedal. counterclockwise, for the left pedal. clockwise).

The use of a special bicycle key will allow you to quickly unscrew the connections by pushing the lever with your whole body. If the pedals refuse to unscrew, in this case it is worthwhile to warm up the junction of the platform with the connecting rod using a burner. It should be borne in mind that heating is carried out with simultaneous cooling of the metal with water. Otherwise, there is a possibility of permanent damage to the parts.

How to remove pedals from a bike: a practical guide

It may be necessary to remove the pedals from the bike if there is a crunch, knock, or other unpleasant situations while riding. It is quite difficult to eliminate such problems. However, having figured out once how to remove the pedals from the bike, you can perform their regular maintenance without resorting to the services of specialists.

Walking on a two-wheeled vehicle has a beneficial effect on well-being. But at the same time, the muscles of the shoulder girdle are practically not involved. Perhaps this is what prompted the developers to invent a bicycle with pedals on the handlebars. In addition to the uniform load on almost all the muscles of the body, you can move on such vehicles at a more impressive speed. Owners of such “iron” horses should also figure out how to remove the pedals from the bike.

Instruments

In the course of work, the following tools may come in handy:

  • Hand wrench. allows access to nuts and disassembly of connections.
  • Bicycle kit. acts as a one-stop solution for a variety of repair procedures.
  • Open-end wrench. suitable for removing pedals on almost all bike models.
  • Special wrench for the system. makes it possible to remove non-standard nuts.
  • Puller. indispensable when you need to work with contact pedals. Allows you to lock the axis when using a hand key.

Eventually

As you can see, dismantling and reinstalling the bicycle pedals is quite simple. However, the process should be approached fully armed, taking care of the availability of all the necessary tools and not forgetting about possible problems that may arise during the procedure.

READ  How to Remove Speed ​​Bike Pedal Sprocket

In order not to puzzle yourself once again with the problems of removing and disassembling the pedal structure, it is enough to constantly maintain the functional unit in good condition, regularly lubricate it and clean it from dirt.

How to remove pedals from a bike

Since the pedal assembly is constantly exposed to the environment against a background of severe mechanical stress, some problems may arise during twisting. Then you need to use two techniques:

  • soaking pedals in solvent to remove accumulated dirt, blocking rotation;
  • heating of the connecting rod and axle allows the threads to be released and the axle to be removed.

It is not difficult to remove the pedal assembly from the bike. This does not require spending too much time and effort. But you need to remember about the preparation of tools, materials, and also be prepared for possible problems. The main thing is to keep the entire system in perfect order. In case of problems, damage, the inconvenience from the process of using the bike is quite large.

In what cases it is necessary to dismantle the pedals?

It is necessary to remove this structural element:

  • if necessary, replacement and in case of damage;
  • for lubrication;
  • to repair the connecting rods.

Before figuring out how to remove a pedal from a bicycle, let’s look at the device and types of this functional part, and also highlight the tools that may be required to work.

Removing the pedals

After preparation, you can proceed with the removal process. For conventional mechanisms, it looks like this:

  • We move the system to the working side. in the direction of the steering wheel.
  • We try to carefully unscrew the pedals from the connecting rod.
  • Remove the plug at the end of the platform, open the lock nut.
  • Unscrew the lock nut, holding the axle at the connecting rod with the second key.
  • Remove the washer (also at the end).
  • Unscrew the cone.
  • We remove the platform from the axle, holding the bearings (it is better to remove them separately, if they are bulk, then put a rag or sheet so that they do not roll far).
  • Pedal removed and disassembled!

It is important not to forget that the left and right pedals are unscrewed from the connecting rod in their direction: on the right axis. the right thread, on the left. the left.

The contact devices are a little more difficult to disassemble, but they will not cause any problems. when twisting and disassembling, a puller is used, which should hold the axis with a small contact pad.

Instruments

In the course of work, the following tools may come in handy:

  • Hand wrench. allows access to nuts and disassembly of connections.
  • Bicycle kit. acts as a one-stop solution for a variety of repair procedures.
  • Open-end wrench. suitable for removing pedals on almost all bike models.
  • Special wrench for the system. makes it possible to remove non-standard nuts.
  • Puller. indispensable when you need to work with contact pedals. Allows you to lock the axis when using a hand key.

What are they made of

The bike pedals are a very simple mechanism. It consists of:

  • Axles. a metal pin, at the end of which there is a thread.
  • Platforms. the surface in contact with the feet;
  • Bearings. provides a rotating moment along the axis;
  • Bolts and nuts.

How to quickly remove and repair pedals on a bicycle

Bicycle pedals are the part of the crankset that propels the two-wheeled bike. A lot of people are seriously into riding a bike, some like to perform virtuoso stunts on BMX. This knot is under severe stress and needs special attention. Preventive measures allow you to avoid many troubles. Quite often, bike owners have such a question, but how to remove the pedals from the bike? How to disassemble or change? In fact, there is nothing complicated here. You only need to go a little deeper into the details and design details.

Eventually

As you can see, dismantling and reinstalling the bicycle pedals is quite simple. However, the process should be approached fully armed, taking care of the availability of all the necessary tools and not forgetting about possible problems that may arise during the procedure.

In order not to puzzle yourself once again with the problems of removing and disassembling the pedal structure, it is enough to constantly maintain the functional unit in good condition, regularly lubricate it and clean it from dirt.

How to remove the pedal from a sports bike

How to remove pedals from a bike?

First you need to equip yourself with a bicycle wrench long enough to create a suitable lever. The tool is placed in a position parallel to the connecting rod. The key turns in the desired direction (for the right pedal. counterclockwise, for the left pedal. clockwise).

The use of a special bicycle key will allow you to quickly unscrew the connections by pushing the lever with your whole body. If the pedals refuse to unscrew, in this case it is worthwhile to warm up the junction of the platform with the connecting rod using a burner. It should be borne in mind that heating is carried out with simultaneous cooling of the metal with water. Otherwise, there is a possibility of permanent damage to the parts.

Removing the pedals from the bike is easy enough, but don’t forget about preparing tools and materials, as well as possible problems. The main thing is to keep the entire system in order, since in case of damage or other problems, the inconvenience of using the bike will be very great.