Is it possible to wash the bike at the car wash

Table of Contents

What to look for when checking into an automatic car wash?

As a rule, what you should do before entering the car wash box is written on the gate. It’s not always true. However, you should always know what you must do before entering an automatic car wash.

Close all windows and sunroof of the vehicle. Lock the fuel tank cap. Turn off the wipers. Be careful, as many vehicles have a rain sensor and the wiper blades may turn on unexpectedly while driving inside a car wash. Therefore, you must turn off the wipers completely.

Also, before entering the car wash, remove all traces of snow and ice from the car body, since in an automatic car wash they can become an analogue of sandpaper, leaving scratches on the car body when water under pressure rinses the dirt off the car body.

When you can’t wash your car in winter?

possible, wash, bike

According to research, you shouldn’t wash your car in sub-zero temperatures below 10 degrees Celsius. Paintwork, like human skin, is very sensitive to extreme temperature fluctuations. The fact is that when you come from a frost to a car wash, you usually drive into a warm box where the temperature is above zero. As a result, there is a sharp temperature drop, to which the paintwork of the machine is very sensitive.

Next, the car is treated with warm water, which adds an additional load to the paintwork due to temperature fluctuations.

Also, do not forget that after a warm car wash, you will then find yourself in the cold again after driving out the gate. Once again, there will be a sharp drop in temperature. You yourself understand that it will not be positively reflected on the paint of the car. Remember that extreme temperature fluctuations also have a negative effect on the rubber and plastic components of the machine.

Yes, of course, after several washes in severe frost, you will hardly notice any changes on the body paintwork. But over time, in the long term, the effects of thermal changes will be reflected in the body paint.

But once again, we repeat that washing a car in severe frost poses a great threat to other components of the car. Most often, door locks, hinges and various seals suffer, which can be damaged due to sudden temperature fluctuations.

Is it true that salt or chemicals on the road can damage the paintwork of a car??

Basically, yes and no. The statement that winter road mud that contains salty alkali has an aggressive effect on the paint of the car is applicable only to those cars that have damage to the paintwork: scratches, chips, or there are places on the body with peeling paint.

If the paintwork of the car is not damaged, then the dirt from the reagent does not have a significant effect on the body. Especially if the dirt containing chemical road deicing agents is washed off from time to time at the car wash.

The same applies to the underside of the car, which is most susceptible to the influence of road reagents. Automakers have long been making car undersides with added protection against reagent salts, using enhanced protection from galvanized metal sheets. So corrosion of the body due to reagents is a problem of the past and applies to old cars or cars with damaged areas of body paint.

Which car wash is better. traditional or automatic?

There are many opinions on this matter. It is impossible to answer this question unequivocally. Everything, of course, depends on the quality of the provided washing services. You can also spoil the paintwork at a regular car wash, where they use dirty rags containing fine sand to dry the body, which can damage the body paint.

It also depends on the chemistry used in the sink. It is not uncommon when the owners of cheap car washes, trying to increase profits, use low-quality cheap auto chemicals, which affects the paintwork of cars.

In particular, some car washes violate the car wash technology. For example, the most common mistake, both in car washes and in conventional car washes, is ignoring the preliminary cleaning of the car body from dirt, as a result of which there is a risk of damage to the body paint.

Therefore, when arriving at the car wash, always make sure that the car wash employees remove coarse dirt from the body under pressure before applying auto chemicals. The same applies to automatic car washes, where, before the main wash cycle, the car must also be pre-cleaned from dirt. Otherwise, there is a risk of damage to the paintwork.

How often should I wash my car through in winter?

According to numerous studies, in many countries the car should be washed as often during the winter as it is during the summer months. First of all, the car must be washed so that in cloudy weather the car is more noticeable on the road, since in snowfall, blizzard or rain, dirty vehicles are often less noticeable on the road.

In theory, a dirty car has a higher risk of being involved in an accident. True, after the traffic rules ordered all drivers to turn on the dipped headlights, the visibility of vehicles on the roads became much better. It is also worth recalling that according to the current traffic rules, you can be fined for dirty license plates. There is no penalty for a dirty car in Russian law. But traffic police officers often attract drivers for dirty cars for the following reasons:

Of course, most often traffic police officers bring drivers to administrative responsibility for dirty license plates than under Part 1 of Article 12.2 of the Administrative Offenses Code of the Russian Federation and under the very formidable Article 12.33 of the Code of Administrative Offenses of the Russian Federation, which is probably applicable only to dirty heavy trucks.

But nevertheless, keep in mind that if pieces of dirt literally fly off your car, then you risk paying a large fine.

So as soon as you have the feeling that your car is too dirty, go to the car wash.

Wash or not wash.

Car wash in winter. wash more often, as little as possible or not wash the car at all? We answer the most important questions about winter car wash. You will learn how often your car needs to be washed, when and where, as well as answers to other questions that motorists often have in winter.

There are many opinions on the correct winter car care. Someone thinks that washing in winter is better only in automatic car washes. And as often as possible. Someone, on the contrary, thinks that it is better to wash the car yourself in conventional car washes by hand. And as rarely as possible. There are also motorists who believe that it is impossible to wash a car in winter, since any washing in winter is a risk of damage to the body paintwork. Who is right? Let’s take a look by answering the most important questions about winter car wash.

Can an automatic car wash damage the paint of a car??

In recent years, automatic car washes are gaining popularity in our country. True, in our country, ordinary car washes are still in great demand in which cars are washed practically by hand. Why, then, in our country, automatic systems for washing vehicles, such as in Europe, are not yet widespread??

The thing is that many car owners are afraid of such car washes because of the myth that automatic car washes can damage the paintwork of the car. But in fact, this is really a myth, unless, of course, we are talking about an unscrupulous owner of an automatic car wash, who does not change brushes and other equipment components on time, and also uses low-quality chemicals.

Yes, once the brushes of automatic car washes really in some cases could spoil the paint of the car. This was due to the peculiarity of the materials from which such brushes were made in the old days.

Today, all car washes are equipped with modern brushes based on polyethylene (PE). polyethylene lint, which cannot damage the paintwork of the machine. True, for this, ideally, the car body should be pre-washed in order to remove coarse dirt from the surface of the paintwork.

At home

Most owners prefer to wash the dirt off their iron friend on their own. this way they will be more confident that everything is done correctly and as it should. There are two options for how to properly wash your bike at home.

The first is do-it-yourself dry cleaning. Before the process, you need to wait until all the dirt is dry, and then you should begin to gently clean it off, moving from top to bottom. Usually, several brushes of different hardness are used for cleaning, for example, a shoebrush, a toothbrush and a bottle brush for hard-to-reach places.

The second option, suitable for heavy dirt, is wet cleaning. Most cyclists prefer to drive their bike into the bathroom and wash it there. To completely fit in the bathroom, you need to remove the wheels and position the bike upside down. First, remove the main dirt with a shower or hose, then you can already proceed to a more thorough cleaning of the bike. This requires: detergent, sponge, brushes.

Usually, special bike shampoos are used, but you can also use a simple dishwashing detergent. Using a sponge and brushes, you can thoroughly clean the bike parts from dirt, but care must be taken that water does not get into the steering column, wheel hubs and bottom bracket, as there are bearings that can rust. It is also undesirable for water to enter the fork through the anthers and into the frame, as corrosion can form inside.

It is necessary to wash the bicycle chain very carefully. there is a lot of dirt that accumulates in the oil. It is more convenient to wash the bike with warm water, as it washes away dirt better. Do not rub off dirt with brute force. this may cause scratches, it is better to wash with a sponge with plenty of water and detergent.

To prevent the parts of the bike from rusting, it must be wiped with a dry soft cloth and left to dry, and after that, be sure to apply lubricant to the bike chain and other parts.

How to wash your bike

Even if the bike is used only for city walks exclusively on asphalt and does not get in the rain, dust still accumulates on the parts, so the bike should be washed about 2-3 times a season. If you get caught in the rain or like dusty and muddy routes, you need to wash your bike much more often. Experienced cyclists advise doing this after every ride.

READ  How To Glue A Chinese Bike Camera

At the car wash

Can I wash my bike at a car wash? If you do not have so much free time to wash your iron horse yourself, you can use the services of a car wash. This procedure takes only 2-3 minutes and seems very simple, but there are several nuances in it. First, do not forget to remove all electronics before the procedure.

Secondly, the employee should be clearly instructed about where the jet should not be directed, namely, to the places where the bearings are located. these are wheel bushings, carriage and forks oil seals. Also, make sure that the worker reduces the power of the jet, otherwise it may wash out all the grease from the parts and bring in sand. It is best to spray water from a distance of about a meter.

In some car washes it is possible to wash the bike immediately with shampoo, however, you should pay attention to what kind of agent this is, since some substances can damage paint and tires.

Many cyclists advise against going to a car wash at all due to the high risk of damage to the bike. If you nevertheless decide to use this method, try to find an employee who understands all the specifics of this procedure, but rather do everything yourself.

It is up to you how to wash the bike, at the car wash or on your own, but do not approach this issue carelessly. If you wash your bike incorrectly, you can greatly shorten its lifespan.

Where to go?

And washing your bike correctly means, first of all, choosing a place where you can do it properly. The most logical thing for many people to wash their vehicles in the yard of the house. All you need is:

  • water;
  • soft tissue;
  • cleaning compound.

You don’t even have to bring the bike home. Therefore, the dwelling will remain in perfect order, and there will be no need to clean up the dirt there. Drying the bike is possible (in good weather) in the same place where it was cleaned. But some cyclists prefer to use the garage for washing, or rather, the concrete area at the entrance to it. On the same site, the bike is dried, and after drying, it is stored inside the garage or sent on a new trip, depending on the circumstances.

When traveling in nature, cyclists are often faced with severe blockages in their vehicles. Sometimes the dirt even blocks further movement. Therefore, it is often necessary to wash the bike in nature, without using any devices or ready-made platforms.

Important: washing is required if lumps of dirt get between the wheel and the wing. Water for cleaning can be taken from any body of water, unless it falls under environmental restrictions.

The hardest part of washing bikes is at home. But city apartment owners don’t have much of an alternative. they have to clean their bikes in the bathroom. The procedure must be carried out with great care and will take longer than usual. And even the most tidy people then need to clean the floors. The question may sometimes arise: is it possible to wash a bicycle at a self-service car wash.

This procedure is necessary if you have been cycling for a long time off-road in wet weather. Powerful high-pressure jets will remove almost all accumulated dirt.

Important: only bushings and transmission should not be subjected to such cleaning. Once there, water under high pressure will simply disrupt these subtle mechanisms. Therefore, you will either have to work very carefully, or turn to professionals for help.

How to properly wash your bike?

Cycling is very pleasant and healthy. But for the bike to be enjoyable for as long as possible, you need to know exactly how to take care of it. Including such a moment, how to wash the bike.

Features of the

No matter how careful cyclists are, no matter how diligently they avoid puddles and mud, the bike will still be covered with various blockages. Splashes of water fall on it, dust sticks, sometimes stains appear. The problem isn’t just that it looks bad.

Dirt and dust get into the mechanisms, reduce their service life and can even lead to very unpleasant consequences, to accidents. Therefore, every cyclist should know how to wash his “steel / aluminum horse” so that it is both clean and washing does not become torture.

Other subtleties of washing bicycles

The washing frequency is determined by:

  • weather conditions;
  • type of surface;
  • the frequency of off-road trips;
  • riding style;
  • cyclist activity.

Those who ride short distances periodically on city streets may limit themselves to cleaning the bike before the start of the season and at the end of it. But even a seemingly insignificant manipulation carried out in a city apartment causes a lot of inconvenience. It is advisable to disassemble the bike into parts in order to wash each one as thoroughly and fully as possible. Consistently:

  • remove all large pieces of dirt;
  • remove the wheels;
  • remove tires;
  • remove the chain;
  • dismantle shifters, switches, brakes;
  • prepare cleaning supplies.

The frames can be washed simply in the bathroom. They are doused with water from the shower head or washed by hand.

How to pre wash your bike in the car wash

Rub hard dirt with hard, and stains and streaks with soft sponges. After removing the blockage, rub all problem parts with a clean, dry cloth. Important: it is better to wipe all pipes dry several times.

When the bike is washed under the shower, you need to be careful that moisture does not get into the internal cavities. The tires are scrubbed with hard sponges, applying a strong pressure of hot water. It should be remembered that this procedure will take a long time. It is not possible to quickly remove dirt, especially if the tread is deep. Rims and spokes should be washed under low pressure. It is highly recommended to wipe them with a wet sponge and dry rags.

The sleeves and their adjoining parts are wiped off with slightly damp cloths. They absolutely must not be washed under a tap or shower, even if the pressure is not too strong. If water does get inside, you will have to change the lubricant.

Cleaning bicycle chains deserves a separate discussion. It can be done by various means:

  • manually (with a brush);
  • special chain washers;
  • grinding machines;
  • in trays with kerosene.

You should devote maximum time and effort to washing the chain. Wipe off dirt with stiff brushes (suitable for shoes). It is necessary to work strictly with gloves. A thick, unnecessary rag is placed on the floor. It is necessary to clean out the dirt longitudinally from both sides.

But an even better option turns out to be the use of a special chain washing machine. This tool will help remove literally petrified particles. It is also extremely useful for bicycles with a fixed chain. It is necessary to resort to a grinding machine only when urgently needed. It can severely cut the chain and leave unpleasant looking marks on it.

This procedure is recommended if the chain has already worked a lot and additional damage is not too terrible for it. In addition, the sander will not be able to clean out the dirt in the gaps between the rollers. Washing with kerosene is good because you don’t have to make any effort. However, it will take 12 to 24 hours for the kerosene to wash away the dirt in the bath; then wipe the chain with dry clean rags.

The switches are cleaned with damp rags. Abrasive compounds cannot be used. The same requirements apply to brake cleaning. After removing the pads, they are wiped, and the dirt adhering to the clamping mechanism is removed with a slightly damp sponge. Then wipe the cables, lay out all the parts and allow them to dry completely.

It is also advisable to clean the stars by hand. Since they are not only covered with dirt, but also with oil, it is advised to use dishwashing detergents or other mild cleaning agents at this stage of cleaning. Be sure to use, of course, hot water. They work again, first with hard, then soft sponges. Important: maximum attention will have to be paid to the gaps between the teeth and sprockets, and the system must be washed from top to bottom and nothing else.

Another option is to use a Karcher foam bike wash. Make sure to keep the hose as far away from the bike as possible. It is worth remembering that low-quality paint can be knocked off the frame with a powerful jet. When the wash is over, in any case, you will have to grease the bushings and the carriage from the outside. Only after that the bike is assembled back.

Can You Ride A Tricycle Through The Car Wash? | Bike Car Wash!

When washing by hand, you can use a car or bicycle shampoo. It is also advised to prepare also degreasers and chain lubricants. It is very good if the bike is standing upright or leaning against something during cleaning. Experts recommend removing lights and bike computers first. It is also worth treating the chains and sprockets with degreasers: this not only helps in cleaning, but also prevents the rims and brake discs from becoming clogged with grease.

If you have to wash your bike without a degreaser, avoid using too much pressure from the cassette and derailleur sides, as well as from the rims. Violation of this rule results in oil getting on the pads.

In theory, they can be cleared, but this is very difficult, and normal braking cannot be restored. After removing the dirt with a stream, the surface is covered with shampoos. After that, you will have to wait from 1 to 3 minutes until the rest of the dirt slips.

For information on how to properly wash your bike, see the next video.

How to efficiently and quickly wash a car in a self-service car wash

The season “tanks are not afraid of dirt” has opened almost everywhere, which means that everyone will go to the car wash and, most likely, at the same time. For those who like to do everything quickly, inexpensively, but humanly, self-service car washes work. Yes, yes, this is where you pay and wash yourself. So what is the secret of success here??

“Read the instructions”, or everything in order

This is the first thing that we were told in response to the question of how it is correct and, most importantly, really good to wash the car yourself. Indeed, almost all owners hang up instructions for using the equipment in the most conspicuous place. But, apparently, such instruction is not enough. So let’s go through all the stages in order and in more detail.

All self-service car washes offer visitors at least five options: prewash, main wash, rinse, wax, shine and dry.

Sometimes there is an option to wash the discs, which is considered to be enough to spend 15 seconds. But if you decide to use it, remember that you should not touch the paintwork while washing.

So, you gave the money to the machine gun, took the pistol out of the casing and select the program:

Pre-wash. It is designed to soften and lift dirt without damaging the car’s coating. You need to roll the whole car from top to bottom. In this case, the gun should be held at a distance of 25-30 cm.

As we were told at the Splash car wash, at this stage there is no need to try to wash off all the dirt, because the chemistry contained in the solution “works with the dirt, but does not wash it off.” Presumably, this step should take you 45 seconds.

Main wash. The name speaks for itself. Changing the distance and angle of the gun tilt, thoroughly rinse all contaminated areas with hot water and foam. Here, the water is supplied under sensible pressure. This procedure should take 120 seconds.

“To obtain the best effect, the solution should be applied and flushed with horizontal movements, moving gradually from the bottom up along the sides of the car, first washing the sidewalls, then the front and stern, and at the end the roof, trunk and hood,” the Splash wash specialists advise.

Rinsing. The mode is needed in order to wash off the foam. Careful diligence can be dispensed with here, because rinsing should not be the last step. It takes 60 seconds.

READ  How to shift gears on a 21 speed bike

Wax. A thin layer of wax will protect the car from dirt, dust and chemicals, which corrode not only snow on their way and which are so generously sprinkled on the roads. Waxing will also take 60 seconds.

Shine and dry. This stage, as it turned out, is no less important for the result than the main wash. By choosing the option, the driver will be able to rinse the car with special demineralized water, flavored with a substance that allows the car to dry faster. In this case, you do not need to wipe the car after the procedure. In addition to protection, the coating must also acquire its own shine. Specialists take 120 seconds for drying and shine.

The last program is very important. rinsing, but not with ordinary water, but through the so-called osmosis. This is demineralized water of very fine filtration. If the client stops at a regular rinse, then it is just regular tap water, which will leave smudges and streaks. It is the last program that allows the car to leave clean, since drying is added there. But this is not a big hair dryer, as you might think, but a substance that helps water to quickly slide down the paintwork.

Tatiana Rakus, CEO of BKF Servis (manufacturer of self-service car washes)

The main problem is that the client does not go through all the washing programs, choosing only to wash with active foam (powder) and water, without using wax and osmosis (purified demineralized water), so the car gets dirty faster and dries longer.

Roman Matsirin, executive director of the “Modern Technologies” company (is engaged in the installation of self-service car washes)

Is it possible to wash a bicycle at a car wash and where to find such?

After the mud baths taken on the rides, you can put your bike in the garage. Itself, as they say, will fall off) But if you keep your bike at home, you will either have to wash it in the bathroom or go to the nearest car wash. Who knows the pros and cons when you wash your horse at the sink, and whether all sinks are taken for such a “jeweler”?

Комментарии и мнения владельцев (1)

There are self-service car washes with a per-minute rate. I think there is at least something you can wash

All sinks are taken, but the “jeweler” does not. If I wash in a car wash, then I wash at a self-service car wash. It is much more pleasant to spoil the bike yourself. In general, such water pressure, as in car washes, does not benefit the bicycle. Especially on the carriage, bushings, forks and other places where dirt can be pushed under the pressure of water. It is best to wash at home in the bathroom, with a cloth, brushes and other machines for cleaning the chain.

I have heard many times that fork-bushings are killed at a car wash, but so far I have never seen such a “victim” in real life. I myself have been washing it at ordinary car washes for many years, I just ask that the bearings do not hit with pressure. If there is a real experience of damage to a bike from a car wash, please share, save more than one bike.

Colleagues, I share. The opinion is not only mine, but also of the most experienced mechanics. The mechanics, however, are also different, and not all of them seek to save the bike owner’s money. But I try to listen to the opinions of other mechanics. So: if you want to use your bike for as long as possible without replacing the bottom bracket bearings, rear hub drum, and the main bearings of the wheel hubs. DO NOT WASH THE BIKE WITH KERCHER. For already stated Z-V reasons. The theory is simple. Water that has penetrated into the inner volume of the bushing through the seals reacts with the lubricant and destroys it. The lubricant then loses its properties. All lubricants used in bearings react with water. All kinds of o-rings on bushings are not designed to withstand pressurized water for a very simple reason. We all love to ride light bikes. The mechanical parts of the bike are optimized for weight, not for working at great depths or under water pressure. A typical real (and massive) example of damage from washing: destruction of one (!) Left carriage bearing. The bearing is destroyed, which, due to the design features of the carriage assembly, is less protected from the jet under pressure. The argument for long-term performance of nodes is certainly not the only one that can be taken into consideration. For example, if you train on the ground 6 days a week, 1 workout and 1 roll a day, and on the 7th day you have a rest day. just a calm ride along a flat 50 km, while your bike is serviced by the mechanics of the national team, then the issue of saving bearings may not be so acute. In the end, they will crumble. will replace. It’s more important to wash your 15 team bikes quickly after every messy day rather than wiping them down with a cloth and brush before midnight. In this case, of course, Karcher. our everything. But this, it seems to me, is not our case. In our case, I recommend: minimize water when caring for your bike. Yes, when wiped dry, you will, oh horror, scratch the varnish and, oh horror, your frame will become dull and will not shine so much in the sun. In return, you will be able to enjoy the fascinating sound of impeccably working bicycle mechanics for many times longer. And you can significantly reduce the time of communication with mechanics (unless you know how to change the bearings of the carriage and the drum yourself). The following recommendations. for ordinary normal people who love to ride and sometimes get into the mud (not for national team athletes and not for those who have a specialist on a salary who looks after their bike). What to do if you have finished your favorite bike? Very simple. Let it drain and dry first. Then you will need 3 things: a brush, a rag and liquid lubricant (and you can do without a brush, it just will speed up the processing of hard-to-reach places). Take a brush and go dry all over the bike (frame, wheels, brakes, cassette, sprockets. Dirt will crumble. Now with a rag. Derailleurs, chain. The bike is clean. Lubricate the chain with liquid oil, smear the chain backwards, wipe the chain dry from the outside with a rag. Everything! The bike is ready. With this care it will serve for a long time, with a minimum of bearing wear. by putting it in the external order in the above described way, you will put it on the balcony (in the closet) for a week or longer, until the next ride.It will be much better if you ride it for at least half an hour, for example, the next day or immediately after Then the water, if it nevertheless penetrated into the bushings, will dry out from friction, and will not calmly eat up the lubricant and steel, which it will be able to reach, within the time given to it. my advice: it is better to do without washing.

Once I washed my bike in the wash after a mud ride, when the rags and brushes were no longer taken. However, even in the sink, it was not possible to wash it completely. There were no damages, I saved my personal time. I gave 100 rubles for the car wash, friends said that sometimes you can negotiate for free.

“Mine, my chimney sweep. Clean, clean, clean, clean! ”

We proceed to the sink, armed with a sponge, liquid detergent and a dry rag. It is necessary to prepare a washing solution: pour a detergent into warm water (or better a car shampoo). Try to wash the frame so that no water gets on the derailleurs, chain, stars, brakes. After you have washed your iron horse, you need to wipe it dry with a cloth. Surface stains can be removed with car polish.

Can I wash my bike in the bathroom or shower?

If you don’t feel sorry for your plumbing, then of course you can, but do not forget that the bike cannot be washed under the pressure of water and try to avoid water getting on important components.

Can I wash my bike chain?

The answer remains the same bike chain can and should be washed! This extends its lifespan and improves ride quality.

The bike chain must never be washed with water.

And what, then, to wash? Bicycle chains are cleaned with solvent. Procedure:

After washing, the chain will need to be lubricated. We will tell you how to do this correctly in the next article.

Let’s summarize

The bike must be looked after, cleaned, washed and lubricated. Then riding it will always be enjoyable. And finally, we present a list of popular questions once again and give a short answer to them.

Can I wash my bike?

Can the mountain bike be washed? Is it possible to wash a speed bike?

Yes, and do it the way we wrote above.

Can the pressure washer take water from the container??

It depends on the model of the sink. There are models that can take water from the tank using a hose with a filter. The container must be above ground level, otherwise the motor will not cope with the work. There are sinks that can use water from sources located 1 meter below ground level, but it is not recommended to do this for a long time. The sink also cannot run dry, so always keep an eye on the amount of water in the container.

How to prepare the mix and attachment for use

  • Following the proportions indicated by the manufacturer of the detergent, dilute it with water in the container of the foam lance and stir.
  • The bottle must be connected to the nozzle and the nozzle itself to the gun. The amount of foam can be adjusted with the regulator, and the spray width is adjusted at the nozzle.
  • Foam should not be applied to a hot body. If the car gets hot in the sun, let it cool down. High temperatures will cause the foam to dry out too quickly.

Can the paintwork be damaged by the sink??

The risk of damaging the coating of the car depends on several factors: distance to the car, spray angle, water focus, and also the quality of the coating itself. Machines with paint peeling are at risk. do not bring the nozzle too close to them. Also, be careful when working with units producing 170 or more bar.

Here are some situations in which there is a risk of damage to the paintwork:

  • A narrow stream of water works at close range. This should not be allowed. start working 50 cm from the cover, and then wash your car at a distance of 15-30 cm from the car.
  • Paint may peel off in areas damaged by corrosion.
  • If the body has been repainted and done poorly, the paint can also begin to flake off.
  • When working at an angle of 25-45 °, the risk of damage to the paint will be minimal.
  • The rotating nozzle (tornado) works hard, it is best to avoid using it when washing a car. It is better suited for cleaning tiles, fences, local area.

Correct car wash with a pressure washer

This article focuses on the process of washing cars with pressure washers. Mini washers for cars are very useful equipment that can significantly reduce the time for cleaning the car from contamination. The sink takes water from a water supply system or a container with water using a motor and a pump. The use of special nozzles allows you to reduce water consumption by up to 80% when compared with using an ordinary hose.

How to wash with a pressure washer?

Do not wash your car in direct sunlight. Before starting work, make sure that all doors, windows and sunroof are tightly closed on the vehicle. Be careful when turning on the car wash, as in the first second the unit can give out increased pressure that can damage the car’s coating. When turning on the device, direct the nozzle to the side and only then transfer it to the car.

It is best to apply the foam to a dry surface, but only if it is not too dirty. If the level of contamination is strong, then you should first wash off the dirt with a wide jet.

Start working at a distance of about 60 cm, then you can move the attachment a little closer. It is not recommended to work at a distance of less than 15 cm. You also need to maintain an angle of 25-45 °. this will wash off dirt so that it does not harm the paintwork of the machine.

For effective foam formation, special nozzles are used. In the next section, we will describe exactly how the foam works. Always use only products specifically designed for pressure washers. Foam is best applied from the bottom up. this way it will adhere more firmly to the surface.

READ  How to Assemble a Speed ​​Bike Rear Wheel Hub

After applying the foam, wait about 5 minutes for the detergent to soften the tough dirt and affect the oil stains. After that, rinse off the foam, holding the gun at least 30 centimeters apart. At the same time, point the nozzle down.

Remember to wash the underside of your car. it is often heavily soiled. To do this, use a special nozzle that allows you to spray water at an angle. It needs to be resting on the floor to eliminate recoil.

In the last step, you can remove the high pressure nozzle and rinse the machine without it.

How to store your sink?

When the sink is not in use, there should be no pressure inside. When you finish working with the device, turn off the water supply and hold the trigger pressed until water stops coming out of the nozzle. After that, you need to turn off the sink.

Store the pressure washer in a warm place. This will keep the mechanism and attachments intact. If the temperature of the storage room is low, use a special antifreeze solution for the pump (Pomp Guard).

Safety when working with a pressure washer

When using the washer, keep in mind that water comes out of it under high pressure, which can damage the skin or paintwork. It can be 30-80 times higher than that produced by a conventional hose. This will be most noticeable when working with nozzles that give a narrow stream of water. When turning on the sink, point the nozzle to the side.

Recoil occurs when the washer is turned on. be careful and hold the gun firmly. It is best to choose a flat surface for work on which you can stand firmly.

Never point the nozzle at people or animals. water can seriously damage your skin. It is also best not to work close to power lines. If there is such a need, you must maintain a distance of at least 2 meters.

How to wash your bike?

In dry weather, such a need rarely arises, but after riding in mud and slush, the bike will definitely need to be cleaned. Can the bike be washed? If you do not pour water on it with buckets, then, of course, yes. Ideally, the washing process is best done outdoors or in a garage.

How can you wash your bike and what you need for this:

detergent (can be standard, for washing dishes).

If there is a lock on the bike chain, it is better to remove it and clean it separately so that dirt does not get into the rollers. It is worth starting washing from the lower pipe, since it is there that the largest layer of dirt is located. Then you need to walk over the rest of the frame. In places with difficult access (for example, a carriage assembly), you can wield an old toothbrush. Wheels can be removed and washed separately. During washing, you should avoid “vulnerable” places of the led, for example, bearings, forks. Finally, wipe the bike dry with a dry cloth.

How to care for shock absorbers?

In order for the bike to continue to ride successfully without any complaints from the rider, it is worth figuring out how to maintain the bike fork.

There are 2 types of service:

Intermediate. care for a pair of friction: “legs” and “pants”. They are protected by a rubber boot, but not 100% protected from dirt and water. Therefore, first of all, during intermediate maintenance, you need to remove the “pants” by unscrewing 2 bolts from the bottom of the fork, and clean them from the inside, then put new grease and reinstall them.

Complete. includes replacement of oil and seals in the damper. This is more complicated and requires a repair kit, bike tools and fork knowledge. If all this is not there, it is better to contact the workshop.

How to properly lubricate a bicycle fork? The process takes place in several stages: removing the plug from the mount; parsing it into its components; applying lubricant to active parts of the system; collecting and installing the plug back.

Should You Jet Wash Your Bike? | Maintenance Monday

Another common question: what kind of oil should you put in the bike fork? Fork lubricants can be grease or liquid. Which one is right for a particular product? Better to focus on the manufacturer’s opinion. Experimenting with gear and machine oils can negatively affect the condition of the fork.

Bicycle chain maintenance

Cycle chain links constantly rubbing against each other need regular lubrication. But before doing this, you need to know how to properly clean, wash and generally care for the bike chain (for example, from the Discovery brand).

So, how to wash the chain of a two-wheeled “friend”. a bicycle:

Washing the bike chain in solvent. This method is best suited for chains with detachable links. chain locks. It is necessary to remove the bike chain from the transport and place it in a plastic bottle, after filling it with solvent. It remains only to thoroughly shake this “cocktail”, then remove the chain and rinse it under running water.

For him, you will need to purchase a special machine. a clinging machine. Their main plus is that the chain does not need to be dismantled for cleaning. The principle of operation of various models of machines is almost identical and boils down to the fact that you need to pour the cleaning agent into a special container, tuck the chain into the guide rollers, close the lid and turn the cycle completely several times until it is completely cleaned. At the end, all that remains is to drain the cleaning agent.

After getting it in shape, it’s time to lubricate the bike chain.

There are 3 ways to lubricate your bike chain:

To drip the links with a special tool, each separately (for this you need an oiler).

Apply an aerosol spray (you need to additionally purchase a can with it).

Dismantle the bike chain and boil it in a thick lubricant.

It is best to lubricate every 50-100 km of cycling or if you hear a specific rustling sound while riding.

For lubrication, you can use:

have convenient packaging, can be used with any model of bicycles, excess grease can be easily removed with a cloth

sold in bottles with a special spout that helps to conveniently apply lubricant, you can use an ordinary syringe to apply them

durable, resistant to temperature extremes, protect against corrosion

convenient and economical to use, repel dust and moisture

withstand high pressure, have good penetrating ability, contain antistatic agent

After all the links of the bike chain have been processed, it is worth eliminating the excess lubricant with a rag, otherwise dust will stick to the lubricated places.

Prevention of gear shifting systems

The switches must function flawlessly so that the climbs and descents of the bike go smoothly. The bicycle rear derailleur is lubricated as follows:

unscrew and disassemble the rear derailleur;

wipe and lubricate it (it is advisable to also lubricate the spring and washer);

The function of the switches also depends on the condition of the cables. Lubrication of cables of any type of bicycle is carried out only from the inside of the “shirts”. If you do this outside, then dust will adhere to them. To clean and lubricate the cables, you will need to unscrew them, loosen them and pull the “shirts” out of the slots on the frame. After the end of the procedure, return everything to its place.

The cables that go through the bike are responsible for the correct function of the speed switch. The correct operation of the switches depends on how tight / loose the cable is. During operation, the cables can stretch, which negatively affects the functioning of the switches. Accordingly, it is necessary to tighten or loosen the adjusting screw. The procedure is repeated until the correct operation of the switch is achieved.

Bicycle care: 6 basic rules for washing, lubricating, storing your bike

Regular and proper care of any type of bike is a 100% guarantee of an increase in its useful life and an increase in the level of safety while riding. In addition to the neat appearance, do not forget about the brakes, shock absorbers, chains and other elements of this transport. Each stage of great care has its own nuances. Which ones? Read more about this in the article.

A nuance: most electric vehicles do not require as much care as a bicycle. It is enough to keep the device clean and recharge it on time.

Brakes led

A common question is: why do bike brakes squeak? There are several reasons depending on their type:

V-brake. if the pads are made of hard rubber, then the unpleasant squeak from them is quite strong. The wheel rim squeaks if it is very dirty or worn out and needs to be replaced. In addition, the pads must be strictly parallel to the rim, without skewing, otherwise annoying creaking cannot be avoided.

Disc brakes. the rear and front disc brakes must be kept clean. The material from which the rotor is constructed is also important: the softer the steel, the quieter the brakes will be.

How can you lubricate disc brakes on a bicycle? The answer is nothing, otherwise they will not fulfill their purpose.

To eliminate the creaking of the brakes, you need:

regularly clean the rim. wipe it with thinner or gasoline to remove the rubber from the worn pads, which has stuck to the rim and increases the friction force;

How and where to store your bike?

A haven for your “iron horse” should be chosen carefully, for its own safety, integrity and preservation of operational qualities.

How to store a bike at home. 2 types:

Assembled. it is better to hang the led on the wall so that the wheels do not come into contact with the floor. If during such storage the pressure in the tires drops, then the wheels will not deform. In rooms without heating, it is better not to leave the bike bike, since the rubber can crack.

Disassembled. the wheels and saddle must be removed from the bike. All this is packed in fabric or plastic bags to protect it from dust, and can also be hung on the wall. The saddle should also be kept warm to prevent deformation of the saddle cover.

How to store a bike in the stairwell? This place can be chosen only as a short-term shelter for the led, since even if the transport is equipped with a lock, there is a high probability of its theft by intruders. There is a lot of traffic in the entrances, so you should choose more “secluded” places for storage: a glazed balcony, a garage, a storage room.

Tip: if you want fewer storage problems, you should think about purchasing a compact electric unicycle, gyroboard or even an electric scooter. the latter folds elegantly, so that it can even be stored in a closet. And the newfangled electric rollers can be thrown onto the shoe rack.

And the last question. how to store your bike in winter? First you need to wash it thoroughly, clean and lubricate the chassis, chain, bushing. The led is sent for wintering only after it is completely dry and the grease is absorbed.

So, bike care is necessary and important. Without timely cleaning and lubrication of the chain, shock absorbers and other things, the bike can fail at the most crucial moment. Most of their described procedures are within the power of everyone, the exception is that if you need to disassemble the parts is large, you cannot do without the help of the masters. Cycling bikes do not like dirt and severe frosts, so the rider’s task is to organize suitable storage conditions for the bike, so that at the beginning of the season there is no need to repair the two-wheeled vehicle.