How to Shoot Speed ​​Bike Stars

How to remove a rear sprocket on a speed bike. How to change sprockets on a bike?

The bicycle is becoming more and more popular nowadays. This is due either to paid parking and the high cost of gasoline, or to the currently fashionable healthy lifestyle.

speed, bike, stars

But almost everyone loves to ride a bicycle, but not everyone knows how to properly care for it. Naturally, over time, parts fail and they should be replaced with new ones or serviced.

As part of this article, we will talk about bicycle sprockets and how you can disassemble and care for them.

Why you need to change sprockets on a bike?

The sprocket on a bicycle has one of the main roles that affect ride quality and speed. During the use of a two-wheeled vehicle, a load is exerted on all its component parts.

Replacing the sprockets is essential for proper function and gear shifting. If you do not repair parts immediately after damage, there is such an option that broken parts will accumulate and repair will be quite costly, in some situations it exceeds the cost of the bike itself.

Bicycle sprocket design

The mechanism externally has several stars of different sizes, which are fixed with a bushing. After that, everything is connected with a lock nut.

Asterisk options:

  • The usual version is that the stars are connected to each other by a plastic spacer;
  • Spider cassette. cassettes made in the form of stars, fixed on an aluminum frame;
  • On several spiders. devices that have a high cost and are usually installed on professional and expensive models. The appearance has 2 spiders, which are connected by sets of stars;
  • X-Dome is a monolithic system that connects the drum to the lid on the opposite side;
  • OpenGlide. Most Relevant for Road Bikes.

How to remove sprockets from the rear wheel of a bicycle?

It is absolutely not difficult to disassemble the device for replacement, but you should be careful and have a couple of free hours in stock.

In some situations, the disassembler initially spends 15 minutes, and another person without the necessary skills can handle it in 1-2 hours.

That is why it is difficult to answer the question of how much time can be spent on a laborious process. In most, all stars have the same parsing method, since they have almost the same structure.

Helpful hints for parsing:

  • How the parts are removed, in this order they should be installed. This advice will help from confusion and waste of extra time that can be spent remembering where a certain detail came from;
  • After parsing, every detail needs to be inspected, perhaps it does not require replacement, but a banal cleaning is simply necessary.

Required tools

In order to remove the sprockets from the bike, you must:

  • A puller suitable for the slotted nut and circlip;
  • Whip. a metal key, consisting of 10-20 links;
  • Adjustable wrench.

Procedure

Step-by-step instructions for parsing:

  • The bike is installed with the wheels up and is in a stable position. The bike must stand on a flat surface and not carry out additional movements that can adversely affect the removal of parts;
  • We remove the wheel located at the back, this can be done using a wrench of the appropriate size. The chain for parsing the star is removed in order not to interfere;
  • With a whip we fix the cassette in one place, we untwist the cassette itself using a puller put on the nut;
  • After that, we remove the plastic ring, which serves as a kind of protection and establish a further front of work (directly install a new one or try to clean and lubricate the parts).

How to replace a sprocket on a bike?

Replacing the sprocket should start with removing the old one, respectively, only then start the installation. If an old part is installed, it must be cleaned and lubricated, only then install.

In the case of a new one, you need:

  • We put on a protective plastic ring;
  • If the stars themselves are not fastened to each other, then they should be put on one at a time, starting with a large one and ending with a small one. We install small rubber pads between the stars;
  • We screw it with a nut, this must be done directly with a wrench. Twisting is carried out according to the hour hands;
  • We fix the nut and check the movement of the nut.

Caring for bike sprockets

Needless to say, all mechanisms require maintenance, otherwise they will quickly fail. Cleaning the transmission from dirt as it gets dirty will significantly extend the life of the part.

You can clean the bike structure according to the following principle:

  • Release the brake and remove the rear wheel;
  • Inspect the inner cassette for dirt. If the dirt is strong, then without removal it will not be possible to clean, in the case when the dirt is minimal, then you can clean it directly on the bike;
  • Use coarse-bristled brushes for cleaning, but they should be small enough to get into hard-to-reach areas. An old toothbrush that is not planned to be used for its intended purpose is suitable for such cleaning;
  • Initially, a rag should be dipped in kerosene and only after that start removing dirt from the sprocket;
  • After cleaning, apply grease to the brush and wipe over the teeth. Then install back.

In order not to change the asterisks, you should constantly carry out proper care and diagnostics. Spending a few minutes of your time once a month to lubricate the sprockets, you can protect yourself not only from large costs, but also wasting extra time.

Therefore, it is much easier to take care of in a timely manner than to repair your bike, especially if you use it often enough.

If a breakdown still happened, you should not be upset, but make every effort to fix it yourself.

Change the sprockets on the rear wheel of the bike

The drivetrain plays a very important role in the operation of the entire bike, so you must carefully monitor the wear of its individual parts. This is especially true of the rear wheel sprockets, which fail over time. A worn sprocket must be replaced as soon as possible, and it will not be difficult to do this.

Required set of tools

Before starting the replacement process, get yourself the tools you need to use. It:

  • Whip
  • Cassette remover
  • Rozhkova and adjustable wrenches

How to properly disassemble a cassette?

First, remove the rear wheel from the bike. This is very easy to do. Unscrew the nut with a wrench and release the chain. Owners of mountain models just need to press on the special mount and the wheel will be dismantled. Next, we install a removable device on the slotted nut of the cassette. Here we need a whip that will prevent the cassette from turning. While we rotate the puller with an adjustable wrench, hold the largest star with a whip.

The process of dismantling and replacing the sprocket

Using the nut, unscrew the cassette and remove it from the wheel. We carefully examine the stars and determine which one has become unusable. Start with the smallest and end with the largest. The bike drivetrain is designed in such a way that you can only replace the worn out sprockets and not the entire cassette. Therefore, after examining the cassette, you remove the used parts from it and replace them with new ones. It is very easy to pull the star out of the cassette, this is facilitated by special rivets. The main thing is to carefully remember the order of the stars, so as not to get confused with their installation back. In the configuration of some bikes, you may find so-called “spiders”. It is a group of several stars that are inextricably linked. In this case, you will have to replace the entire spider. Many cyclists face the following problem. After replacing several stars, there is a great discomfort in the operation of the chain. This is due to the fact that the chain has already passed a certain mileage, has worn out and now it is difficult for it to interact with new parts. Therefore, experts recommend the simultaneous replacement of the chain and worn sprockets. This greatly minimizes the complexity of your bike’s drivetrain.

What You Should Know About Singlespeed?

If you own a single speed bike, the process of replacing the chainring will be simplified to a minimum. You just need to open the retaining ring. If your own ring has become unusable, it must be replaced immediately, even if you are not going to replace the stars in the near future. Otherwise, the chain will lose its fixation, and this threatens with backlash. The process of replacing the ring is very simple, you do not need to perform the slightest forceful manipulations. Therefore, if you are talking about a single-speed bike, everything is very easy and understandable here. However, owners of such models should carry out the process of dismantling the cassette only if one or more of the largest stars have worn out. If a small asterisk begins to fail, this is not a cause for concern. Whatever you ride, remember that both the simplest road bike and the super-fast bike need a proper transmission. A badly worn chain and stars will not allow you to drive even a couple of meters. Pay close attention to the mechanics and timely replace worn-out parts. A working bike is the main guarantee of your safety and a cool, trouble-free ride!

how to replace the rear sprocket on a speed bike

There are not many key parts in a speed bike. The main ones include the stars, which serve to switch speeds with the provision of gear ratios in the transmission. With the constant operation of the bicycle mechanism, worn sprockets are formed. This is facilitated by the usual physical process. friction. What is the threat? The chain starts to jam and simply slips deformed parts.

The problem that has arisen requires an immediate solution. If the question is ignored, then any movement on the road will turn into a solid negative. The model of a modern bike allows you to change a worn out part. Our article will tell you how to replace the rear sprocket on a speed or mountain bike.

Disassembly process of transmission cassette

Some theory beforehand. On the rear wheel there can be two variants of parts associated with gear shifting.

  • Transmission cassette. This product features modernity and innovative spline mountings that attach to the hub axle.
  • Ratchet. A somewhat outdated model typical of inexpensive speed bikes. The set contains no more than seven gears. As for the mount, it has a thread with external installation parameters.

Let’s focus on the ratchet right away. Changing the rear chainring on a ratchet bike is not possible. Only change the entire component completely.

Therefore, the topic of the article will be a problem describing a situation when a bicycle cassette star needs to be replaced. As for the set of stars in the transmission, up to 11 pieces are possible, depending on the bike model.

Ratchet and cassette elements

So how do you change the rear sprocket on a speed bike? Consider the algorithm of actions.

  • Take the bicycle key for the rear wheel and dismantle it. We sequentially unclench the levers and loosen the fixing of the nut.
  • Now it is the turn for the axle nuts. Using another key, turn off the mount.
  • The next step involves unscrewing the bearing cone and pulling it out.
  • We take out the axis with all the elements.

Sleeve recessing process.

  • We take a special tool. a cassette remover. We insert it into the slots.
  • The whip is placed on the largest sprocket. We make rotational movements clockwise.
  • At the same time, using an adjustable wrench, the puller rotates in the opposite direction.

The preliminary stage is over. Such simple actions are possible in ordinary household conditions. We emphasize that if more than one star is worn out, but several, it is better to replace the entire cassette at once. This option is also desirable if the largest star is damaged.

And one more recommendation. We put all small parts, washers and nuts in a certain place, so that later we do not search all over the room

Star stripping process

How to change the rear sprocket on a bike after the first stage has already been passed.

  • Removing the mount.
  • Detach the cassette from the rear wheel.
  • We make a thorough inspection.
  • Determining Wear Sprockets.
  • We remove the worn out product.
  • Pay attention to the arrangement of the stars and the sequence of fasteners and washers between them.

Cassettes, compare favorably with ratchets, in that each worn part can be freely removed separately.

A separate recommendation would be to replace the chain, which is also worn out, along with the sprocket.

Stages of installing new stars

How does assembly work when replacing a bicycle cassette chainring?

Let’s look at the steps.

  • Install a new sprocket and fix it.
  • Assembling the cassette in reverse order.
  • Using a puller, mount the drum on the slotted area.
  • The drum must first be leveled.
  • Next, we carry out the process of assembling the sleeve. All actions described in the first paragraph are carried out in reverse order.
  • Install the rear wheel and fix it securely.
  • Put on the chain.

It is imperative to check the smooth operation of the transmission. This procedure involves adjusting the rear derailleur.

If everything is done according to the proposed instructions, feel free to get on the bike and enjoy the ride.

How to remove a sprocket from a bike

The sprockets of a speed bike are the main parts of the gearshift system that provide the gear ratio of the drivetrain. According to the degree of influence, they are divided into leaders and followers. The first are located at the connecting rod pair and are called the system. The driven ones are located on the rear wheel hub and are divided into cassettes and ratchets by design.

Over time, the stars wear out, as a result of which they need to be completely or partially replaced. The second option is more common in practice, since wear is uneven. The most frequently used programs are subject to it. The problem, of course, requires a timely solution, otherwise driving will turn into torment. The chain will seize or skip over worn stars. Many modern models allow you to remove the sprocket and put it separately on the system or cassette without replacing the entire components. Read on how to do this.

How to remove and put a system star

The system is a set of three chainrings. If you often have to ride at speed, then the biggest sprocket is likely to wear out. Conversely, with frequent off-road trips, wear will affect the first (smallest) sprocket. Similar to the second, middle sprocket, when the bike is used at medium speeds in conditions of a dirt road or bad asphalt.

On a modern mountain or road bike, the system is collapsible, so it is not difficult to dismantle all the stars. Before work, you need to carefully prepare, namely, collect all the necessary tools:

Remove the system from the bike: 1. Place the frame in a straight position. If you have a stand, you should definitely use it.

Remove the right crank axle fixing bolt with a hexagon.

Unscrew the pedal from the right crank arm. A standard open-end wrench is suitable for this.

Insert the puller into the connecting rod to remove it from the carriage. To begin with, we screw the tool all the way into the thread. It is important that it sit flat on the shaft, otherwise the axle can be damaged when unscrewing the connecting rod. Place the spanner wrench on the puller and screw it in until it stops until the connecting rod is pushed out of the carriage shaft.

READ  How To Change The Hub On The Rear Wheel Of A Bicycle

Remove the system carefully from the chain.

The two stars are usually attached to each other on a so-called spider. The big one remains on the connecting rod itself. Unscrew them with the hex bolts.

This is how the system understands. Replacement and installation looks like the reverse process:

  • Place the desired sprocket on the spider and tighten the fasteners. Change the large part together with the right connecting rod and screw the medium and small stars onto it.
  • Next is the installation of the connecting rod on the carriage. Before this, it is advisable to clean and lubricate the carriage shaft.
  • Carefully place the chain on the system and screw in the connecting rod by rotating the puller in the opposite direction.
  • Tighten the fixing nuts and fit the plugs.
  • Screw the pedal onto the connecting rod.

When replacing one star, it is advisable to clean the old ones. Lightly grease the system components before installing on the carriage.

So just replace the chainring. All listed tools are required. The connecting rod is a delicate thing, and a hammer and chisel is not the best option for removing it. The same goes for keys. It is difficult to replace them with pliers, moreover, nuts can easily “eat”. Well, without hexagons, it is impossible to disassemble the system into parts.

At the end, check the operation of the transmission. whether everything is in order and whether it is necessary to adjust the speed switch.

Change the sprocket on the rear cassette

The set of transmission stars of the rear wheel is several times larger than the front one. The standard kit includes eight components, and in high-speed models (or on a sports bike) there are 9 or 11.

It is worth mentioning right away that a cassette or ratchet can be placed behind. The cassette is a modern version with an internal splined mounting on the hub axle. Ratchets, as an outdated option, can only be found on a budget high-speed bike. The set usually includes 5-7 gears. External mount, threaded, removable tool differs from cassette.

The fundamental difference from the cassette is its integrity. you cannot change the star separately on the ratchet. It’s either all at once, or nothing at all. Therefore, we will consider how to install a new sprocket on the cassette.

As with replacing the leading stars, special tools are required here:

  • cassette remover;
  • chain whip-retainer;
  • adjustable wrench or head;
  • optional: wrenches, chain release.

When removing the cassette, you will need to first remove the rear wheel from the bike and then the axle nuts. At the same time, when replacing the sprockets, you can also clean the chain. you need a squeeze to remove it.

Sequence of work: 1. Remove the rear wheel with a 15 wrench, with eccentric fastening everything is simple. unclench the lever and loosen the fixing nut.

The next step is to unscrew the axle nuts. You will need a 17 key for it. To roll the mount off the rotating axis, we put on an additional nut to fix the axis.

Unscrew the bearing cone and pull out the bearing from the opposite side.

Remove axle with taper and bearing. About the bushing components: if necessary, you can immediately replace them with new ones.

Insert the cassette remover into the slots.

Place the whip on the largest (lowest) star. We will rotate it clockwise.

Use an adjustable wrench or a head to turn the puller counterclockwise.

It is so easy to shoot a cassette at home. Most modern star sets are collapsible, you can install one or two new stars. However, in case of severe wear, when half of the cassette has been worn off, it makes no sense to change them separately. Difficulties can also arise if the largest sprocket has been erased, on which all the others are usually attached.

Can a cassette be dismantled without a puller and a whip? In principle, this can be done with a spline tube and a spanner. The whip can be made by yourself by welding a piece of old chain to the metal handle of the knife.

When replacing individual stars, especially the middle ones, we disassemble the cassette carefully so as not to lose all the spacer and fixing washers. Everything is easier with a cassette on a spider. it does not need to be disassembled, the star is removed separately from its mount.

Rear transmission assembly:

  • Put and fix a new star, assemble a cassette.
  • Using a puller, install the drum on the spline mount of the sleeve. Before tightening, it is necessary to align the drum so that the connection does not wear off under load. The whip is not needed here. just rotate the puller clockwise with effort.
  • Assemble the bushing: insert the axle from the cassette side, then the bearing and the cone on the left side, fix the axle with nuts.
  • Put on the chain and put on the rear wheel.

Check transmission operation and adjust rear derailleur. Timely replacement of sprockets will save you from unpleasant surprises on trips and will, in general, increase the resource of the bicycle transmission.

How to remove sprockets from the rear wheel of a bicycle: step by step instructions

With active riding, the bike gradually wears out. To avoid this, you must constantly look after him. On speed bikes, one of the most vulnerable spots is the rear of the drivetrain. Therefore, sometimes it requires replacement. How to remove sprockets from the rear wheel of a bicycle?

Why is it needed?

The most common problem is chain wear. If not replaced in time, it will begin to bore out stars. Everyone has their own favorite show that they use the most. Over time, the chain on it will begin to spin if a heavy load is applied. Therefore, you need to learn how to remove sprockets from the rear wheel of a bicycle. As soon as such a skill is acquired, you can fix any breakdowns yourself. And this will save you a lot of money on maintenance in the workshop.

Why is this necessary? You can remove the sprockets from the rear wheel of the bike for both regular lubrication and a complete replacement. They will also interfere if you need to replace the spokes on the right side or get to the hub itself.

The difference between a ratchet and a cassette

Before removing the sprockets from the rear wheel of a bicycle, you need to decide on their design. It is important to distinguish between ratchet and cassette. Although they are similar in appearance, they are very different inside.

In the ratchet, the freewheel is installed together with the sprockets. This is such a monolithic system that is simply screwed onto the bushing. The cassette can be disassembled, so you can replace one worn sprocket. Unlike a ratchet, it is not a monolith with a freewheel mechanism, but is put on it.

To remove them, you need different pullers. It is important not to confuse them with each other, because they are not interchangeable. They have different splines. If you are still afraid not to distinguish a ratchet from a cassette, a photo will be an excellent tip in this matter.

How to remove sprockets from the rear wheel of a bicycle?

If it’s a ratchet, then things will be a little easier. If there is special equipment, then even a person who has nothing to do with bicycles can cope with this.

This requires only 2 tools:

  • special puller;
  • adjustable wrench.

First, of course, you need to remove the wheel. Then the stars are removed in two steps. It is necessary to insert the puller into the ratchet, and then try to turn it counterclockwise with a key.

If the mechanism has never been removed, then it can twist strongly (such is its property) and not give in even under great efforts. Then you need to spray the miraculous WD-40 spray there from the thread side. If you leave it like this for a few hours, then the ratchet can be easily removed. It should also be remembered that the larger the lever, the greater the effort. Therefore, you need to take the largest adjustable wrench. Do a couple of jerks and the ratchet will unscrew easily.

You will need another tool to remove the cassette. It’s called a whip. It’s a handle with a piece of bike chain attached to it. If the cassette is turned counterclockwise, it will start to rotate. This is where this whip comes in handy to hold her. Some craftsmen simply use a piece of an old chain instead of this tool. Then everything is the same as when removing the ratchet.

How to remove sprockets from the rear wheel of a bicycle without a puller?

For such an operation, you do not need to purchase a special tool. True, it is much easier to deal with him. In order to remove the ratchet without a puller, you will need:

  • gas wrench;
  • center punch;
  • a hammer.

The ratchet has 2 slots. You need to insert a center punch there and hit it with a hammer. You need to direct it clockwise. You can use a large nail instead. You have to be careful, as there are bearings under this place. With a little effort, you can screw the sprockets.

There is still the inside of the ratchet. It is removed with a gas wrench, which is turned counterclockwise.

How to remove a sprocket from a bike

The sprockets of a speed bike are the main parts of the gearshift system that provide the gear ratio of the drivetrain. According to the degree of influence, they are divided into leaders and followers. The first are located at the connecting rod pair and are called the system. The driven ones are located on the rear wheel hub and are divided into cassettes and ratchets by design.

Over time, the stars wear out, as a result of which they need to be completely or partially replaced. The second option is more common in practice, since wear is uneven. The most frequently used programs are subject to it. The problem, of course, requires a timely solution, otherwise driving will turn into torment. The chain will seize or skip over worn stars. Many modern models allow you to remove the sprocket and put it separately on the system or cassette without replacing the entire components. Read on how to do this.

How to remove and put a system star

The system is a set of three chainrings. If you often have to ride at speed, then the biggest sprocket is likely to wear out. Conversely, with frequent off-road trips, wear will affect the first (smallest) sprocket. Similar to the second, middle sprocket, when the bike is used at medium speeds in conditions of a dirt road or bad asphalt.

On a modern mountain or road bike, the system is collapsible, so it is not difficult to dismantle all the stars. Before work, you need to carefully prepare, namely, collect all the necessary tools:

  • connecting rod puller;
  • spanner key;
  • hexagons;
  • new detail;
  • clean cloth and grease.

Remove the system from the bike: 1. Place the frame in a straight position. If you have a stand, you should definitely use it.

Remove the right crank axle fixing bolt with a hexagon.

Unscrew the pedal from the right crank arm. A standard open-end wrench is suitable for this.

Insert the puller into the connecting rod to remove it from the carriage. To begin with, we screw the tool all the way into the thread. It is important that it sit flat on the shaft, otherwise the axle can be damaged when unscrewing the connecting rod. Place the spanner wrench on the puller and screw it in until it stops until the connecting rod is pushed out of the carriage shaft.

Remove the system carefully from the chain.

The two stars are usually attached to each other on a so-called spider. The big one remains on the connecting rod itself. Unscrew them with the hex bolts.

This is how the system understands. Replacement and installation looks like the reverse process:

  • Place the desired sprocket on the spider and tighten the fasteners. Change the large part together with the right connecting rod and screw the medium and small stars onto it.
  • Next is the installation of the connecting rod on the carriage. Before this, it is advisable to clean and lubricate the carriage shaft.
  • Carefully place the chain on the system and screw in the connecting rod by rotating the puller in the opposite direction.
  • Tighten the fixing nuts and fit the plugs.
  • Screw the pedal onto the connecting rod.

So just replace the chainring. All listed tools are required. The connecting rod is a delicate thing, and a hammer and chisel is not the best option for removing it. The same goes for keys. It is difficult to replace them with pliers, moreover, nuts can easily “eat”. Well, without hexagons, it is impossible to disassemble the system into parts.

At the end, check the operation of the transmission. whether everything is in order and whether it is necessary to adjust the speed switch.

Change the sprocket on the rear cassette

The set of transmission stars of the rear wheel is several times larger than the front one. The standard kit includes eight components, and in high-speed models (or on a sports bike) there are 9 or 11.

It is worth mentioning right away that a cassette or ratchet can be placed behind. The cassette is a modern version with an internal splined mounting on the hub axle. Ratchets, as an outdated option, can only be found on a budget high-speed bike. The set usually includes 5-7 gears. External mount, threaded, removable tool differs from cassette.

The fundamental difference from the cassette is its integrity. you cannot change the star separately on the ratchet. It’s either all at once, or nothing at all. Therefore, we will consider how to install a new sprocket on the cassette.

As with replacing the leading stars, special tools are required here:

  • cassette remover;
  • chain whip-retainer;
  • adjustable wrench or head;
  • optional: wrenches, chain release.

Sequence of work: 1. Remove the rear wheel with a 15 wrench, with eccentric fastening everything is simple. unclench the lever and loosen the fixing nut.

The next step is to unscrew the axle nuts. You will need a 17 key for it. To roll the mount off the rotating axis, we put on an additional nut to fix the axis.

Unscrew the bearing cone and pull out the bearing from the opposite side.

Remove axle with taper and bearing. About the bushing components: if necessary, you can immediately replace them with new ones.

Insert the cassette remover into the slots.

Place the whip on the largest (lowest) star. We will rotate it clockwise.

Use an adjustable wrench or a head to turn the puller counterclockwise.

It is so easy to shoot a cassette at home. Most modern star sets are collapsible, you can install one or two new stars. However, in case of severe wear, when half of the cassette has been worn off, it makes no sense to change them separately. Difficulties can also arise if the largest sprocket has been erased, on which all the others are usually attached.

Can a cassette be dismantled without a puller and a whip? In principle, this can be done with a spline tube and a spanner. The whip can be made by yourself by welding a piece of old chain to the metal handle of the knife.

READ  Bicycle Chain Removal Tool

When replacing individual stars, especially the middle ones, we disassemble the cassette carefully so as not to lose all the spacer and fixing washers. Everything is easier with a cassette on a spider. it does not need to be disassembled, the star is removed separately from its mount.

Rear transmission assembly:

  • Put and fix a new star, assemble a cassette.
  • Using a puller, install the drum on the spline mount of the sleeve. Before tightening, it is necessary to align the drum so that the connection does not wear off under load. The whip is not needed here. just rotate the puller clockwise with effort.
  • Assemble the bushing: insert the axle from the cassette side, then the bearing and the cone on the left side, fix the axle with nuts.
  • Put on the chain and put on the rear wheel.

Check transmission operation and adjust rear derailleur. Timely replacement of sprockets will save you from unpleasant surprises on trips and will, in general, increase the resource of the bicycle transmission.

How to remove a sprocket from a rear bicycle wheel. How to remove a sprocket from a bike

The sprockets of a speed bike are the main parts of the gearshift system that provide the gear ratio of the drivetrain. According to the degree of influence, they are divided into leaders and followers. The first are located at the connecting rod pair and are called the system. The driven ones are located on the rear wheel hub and are divided into cassettes and ratchets by design.

Over time, the stars wear out, as a result of which they need to be completely or partially replaced. The second option is more common in practice, since wear is uneven. The most frequently used programs are subject to it. The problem, of course, requires a timely solution, otherwise driving will turn into torment. The chain will seize or skip over worn stars. Many modern models allow you to remove the sprocket and put it separately on the system or cassette without replacing the entire components. Read on how to do this.

How to remove and put a system star

The system is a set of three chainrings. If you often have to ride at speed, then the biggest sprocket is likely to wear out. Conversely, with frequent off-road trips, wear will affect the first (smallest) sprocket. Similar to the second, middle sprocket, when the bike is used at medium speeds in conditions of a dirt road or bad asphalt.

On a modern mountain or road bike, the system is collapsible, so it is not difficult to dismantle all the stars. Before work, you need to carefully prepare, namely, collect all the necessary tools:

Remove the system from the bike: 1. Place the frame in a straight position. If you have a stand, you should definitely use it.

Remove the right crank axle fixing bolt with a hexagon.

Unscrew the pedal from the right crank arm. A standard open-end wrench is suitable for this.

Insert the puller into the connecting rod to remove it from the carriage. To begin with, we screw the tool all the way into the thread. It is important that it sit flat on the shaft, otherwise the axle can be damaged when unscrewing the connecting rod. Place the spanner wrench on the puller and screw it in until it stops until the connecting rod is pushed out of the carriage shaft.

Remove the system carefully from the chain.

The two stars are usually attached to each other on a so-called spider. The big one remains on the connecting rod itself. Unscrew them with the hex bolts.

This is how the system understands. Replacement and installation looks like the reverse process:

  • Place the desired sprocket on the spider and tighten the fasteners. Change the large part together with the right connecting rod and screw the medium and small stars onto it.
  • Next is the installation of the connecting rod on the carriage. Before this, it is advisable to clean and lubricate the carriage shaft.
  • Carefully place the chain on the system and screw in the connecting rod by rotating the puller in the opposite direction.
  • Tighten the fixing nuts and fit the plugs.
  • Screw the pedal onto the connecting rod.

When replacing one star, it is advisable to clean the old ones. Lightly grease the system components before installing on the carriage.

So just replace the chainring. All listed tools are required. The connecting rod is a delicate thing, and a hammer and chisel is not the best option for removing it. The same goes for keys. It is difficult to replace them with pliers, moreover, nuts can easily “eat”. Well, without hexagons, it is impossible to disassemble the system into parts.

At the end, check the operation of the transmission. whether everything is in order and whether it is necessary to adjust the speed switch.

Change the sprocket on the rear cassette

The set of transmission stars of the rear wheel is several times larger than the front one. The standard kit includes eight components, and in high-speed models (or on a sports bike) there are 9 or 11.

It is worth mentioning right away that a cassette or ratchet can be placed behind. The cassette is a modern version with an internal splined mounting on the hub axle. Ratchets, as an outdated option, can only be found on a budget high-speed bike. The set usually includes 5-7 gears. External mount, threaded, removable tool differs from cassette.

The fundamental difference from the cassette is its integrity. you cannot change the star separately on the ratchet. It’s either all at once, or nothing at all. Therefore, we will consider how to install a new sprocket on the cassette.

As with replacing the leading stars, special tools are required here:

  • cassette remover;
  • chain whip-retainer;
  • adjustable wrench or head;
  • optional: wrenches, chain release.

When removing the cassette, you will need to first remove the rear wheel from the bike and then the axle nuts. At the same time, when replacing the sprockets, you can also clean the chain. you need a squeeze to remove it.

Sequence of work: 1. Remove the rear wheel with a 15 wrench, with eccentric fastening everything is simple. unclench the lever and loosen the fixing nut.

The next step is to unscrew the axle nuts. You will need a 17 key for it. To roll the mount off the rotating axis, we put on an additional nut to fix the axis.

Unscrew the bearing cone and pull out the bearing from the opposite side.

Remove axle with taper and bearing. About the bushing components: if necessary, you can immediately replace them with new ones.

Insert the cassette remover into the slots.

Place the whip on the largest (lowest) star. We will rotate it clockwise.

Use an adjustable wrench or a head to turn the puller counterclockwise.

It is so easy to shoot a cassette at home. Most modern star sets are collapsible, you can install one or two new stars. However, in case of severe wear, when half of the cassette has been worn off, it makes no sense to change them separately. Difficulties can also arise if the largest sprocket has been erased, on which all the others are usually attached.

Can a cassette be dismantled without a puller and a whip? In principle, this can be done with a spline tube and a spanner. The whip can be made by yourself by welding a piece of old chain to the metal handle of the knife.

When replacing individual stars, especially the middle ones, we disassemble the cassette carefully so as not to lose all the spacer and fixing washers. Everything is easier with a cassette on a spider. it does not need to be disassembled, the star is removed separately from its mount.

Rear transmission assembly:

  • Put and fix a new star, assemble a cassette.
  • Using a puller, install the drum on the spline mount of the sleeve. Before tightening, it is necessary to align the drum so that the connection does not wear off under load. The whip is not needed here. just rotate the puller clockwise with effort.
  • Assemble the bushing: insert the axle from the cassette side, then the bearing and the cone on the left side, fix the axle with nuts.
  • Put on the chain and put on the rear wheel.

Check transmission operation and adjust rear derailleur. Timely replacement of sprockets will save you from unpleasant surprises on trips and will, in general, increase the resource of the bicycle transmission.

How to change sprockets on a bike?

The bicycle is becoming more and more popular nowadays. This is due either to paid parking and the high cost of gasoline, or to the currently fashionable healthy lifestyle.

But almost everyone loves to ride a bicycle, but not everyone knows how to properly care for it. Naturally, over time, parts fail and they should be replaced with new ones or serviced.

As part of this article, we will talk about bicycle sprockets and how you can disassemble and care for them.

Why you need to change sprockets on a bike?

The sprocket on a bicycle has one of the main roles that affect ride quality and speed. During the use of a two-wheeled vehicle, a load is exerted on all its component parts.

Replacing the sprockets is essential for proper function and gear shifting. If you do not repair parts immediately after damage, there is such an option that broken parts will accumulate and repair will be quite costly, in some situations it exceeds the cost of the bike itself.

Bicycle sprocket design

The mechanism externally has several stars of different sizes, which are fixed with a bushing. After that, everything is connected with a lock nut.

Asterisk options:

  • The usual version is that the stars are connected to each other by a plastic spacer;
  • Spider cassette. cassettes made in the form of stars, fixed on an aluminum frame;
  • On several spiders. devices that have a high cost and are usually installed on professional and expensive models. The appearance has 2 spiders, which are connected by sets of stars;
  • X-Dome is a monolithic system that connects the drum to the lid on the opposite side;
  • OpenGlide. Most Relevant for Road Bikes.

How to remove sprockets from the rear wheel of a bicycle?

It is absolutely not difficult to disassemble the device for replacement, but you should be careful and have a couple of free hours in stock.

In some situations, the disassembler initially spends 15 minutes, and another person without the necessary skills can handle it in 1-2 hours.

That is why it is difficult to answer the question of how much time can be spent on a laborious process. In most, all stars have the same parsing method, since they have almost the same structure.

Helpful hints for parsing:

  • How the parts are removed, in this order they should be installed. This advice will help from confusion and waste of extra time that can be spent remembering where a certain detail came from;
  • After parsing, every detail needs to be inspected, perhaps it does not require replacement, but a banal cleaning is simply necessary.

Required tools

In order to remove the sprockets from the bike, you must:

  • A puller suitable for the slotted nut and circlip;
  • Whip. a metal key, consisting of 10-20 links;
  • Adjustable wrench.

Procedure

Step-by-step instructions for parsing:

  • The bike is installed with the wheels up and is in a stable position. The bike must stand on a flat surface and not carry out additional movements that can adversely affect the removal of parts;
  • We remove the wheel located at the back, this can be done using a wrench of the appropriate size. The chain for parsing the star is removed in order not to interfere;
  • With a whip we fix the cassette in one place, we untwist the cassette itself using a puller put on the nut;
  • After that, we remove the plastic ring, which serves as a kind of protection and establish a further front of work (directly install a new one or try to clean and lubricate the parts).

How to replace a sprocket on a bike?

Replacing the sprocket should start with removing the old one, respectively, only then start the installation. If an old part is installed, it must be cleaned and lubricated, only then install.

In the case of a new one, you need:

  • We put on a protective plastic ring;
  • If the stars themselves are not fastened to each other, then they should be put on one at a time, starting with a large one and ending with a small one. We install small rubber pads between the stars;
  • We screw it with a nut, this must be done directly with a wrench. Twisting is carried out according to the hour hands;
  • We fix the nut and check the movement of the nut.

Caring for bike sprockets

Needless to say, all mechanisms require maintenance, otherwise they will quickly fail. Cleaning the transmission from dirt as it gets dirty will significantly extend the life of the part.

You can clean the bike structure according to the following principle:

  • Release the brake and remove the rear wheel;
  • Inspect the inner cassette for dirt. If the dirt is strong, then without removal it will not be possible to clean, in the case when the dirt is minimal, then you can clean it directly on the bike;
  • Use coarse-bristled brushes for cleaning, but they should be small enough to get into hard-to-reach areas. An old toothbrush that is not planned to be used for its intended purpose is suitable for such cleaning;
  • Initially, a rag should be dipped in kerosene and only after that start removing dirt from the sprocket;
  • After cleaning, apply grease to the brush and wipe over the teeth. Then install back.

In order not to change the asterisks, you should constantly carry out proper care and diagnostics. Spending a few minutes of your time once a month to lubricate the sprockets, you can protect yourself not only from large costs, but also wasting extra time.

Therefore, it is much easier to take care of in a timely manner than to repair your bike, especially if you use it often enough.

If a breakdown still happened, you should not be upset, but make every effort to fix it yourself.

How to remove a bike cassette

Cyclists often have to service their vehicle on their own. each time it will be quite expensive to contact specialized repair services. Many bicycle elements can be removed and installed quite easily and simply, but there are details that require the use of specific tools and some knowledge. These include the cassette. a part that is attached to the rear hub.

How to remove a bike cassette

First of all, you need to prepare the necessary tool:

  • cassette retaining ring remover;
  • “Whip”. a special key to which a bicycle chain is attached (fragment);
  • adjustable wrench.

You can, of course, do without the specified specific tool. over, there are 2 such methods and both will “work” 100%:

Be sure to prepare an area with a flat surface, which should be within arm’s reach of the bike. this is how you can save and not lose all the parts of the bike cassette.

Step-by-step instructions for removing the cassette:

  • The bicycle wheel is removed, a special puller is installed. You need to pay attention to the correct installation of this tool: its slots must completely enter the grooves of the retaining ring.
  • The “whip” key is taken into your hands and placed on the sprocket so that the fragment of the bicycle chain on the key is on the sprocket teeth. Please note that the handle of the “whip” should be to the right of the cassette, a fragment of the tool chain. at the top.
  • An adjustable wrench is placed on the cassette remover and rotated counterclockwise. Simultaneously with this movement, it is necessary to firmly hold the “whip” key in a fixed position. thus, movements / scrolling of the sprocket are blocked. Note:in some cases, the chain may jump off during this process, which means that the cassette sprockets are very worn out or the key “whip” is broken. Experts recommend throwing a “whip” over a large sprocket. you can get the desired fixation effect.
  • The retaining ring is completely unscrewed, the cassette is removed.
READ  Why Bike Wide Wheels

Be sure to make sure that the removed cassette, as well as the sprockets and all fasteners, are in the removable form exactly in the order in which they were in the original version.

After removing the cassette, you can start cleaning and lubricating it. these procedures are among the mandatory for regular maintenance of a two-wheeled vehicle.

How to install a cassette on a bike

First of all, make sure that the cassette assembly matches the unfolded / removed parts. To facilitate this process, the sprockets have grooves of different sizes (for each sprocket. individual), and the bushing has suitable splines. It is the correct alignment of the grooves and splines that all the sprockets will stand in a certain order.

There are some important things to keep in mind when installing the cassette on your bike:

  • Many cyclists lubricate the bushing surface before installing the part in question. However, experts believe this is wrong. after lubrication (until the entire cassette is assembled and installed), both dust and dirt will have time to get onto the applied lubricant, which ultimately leads to the need for maintenance, repair or replacement of elements.
  • Experienced cyclists lubricate the thread of the retaining ring before assembling the cassette. during subsequent disassembly it will be much easier to unscrew.
  • All sprockets must be worn alternately, but do not forget to put spacer rings between them. In some bike models, you can see not separate sprockets, but a single / one-piece assembly.
  • In many bicycles, to securely install the last sprocket, you need to lightly press it and only then you can screw the retaining ring.
  • After the locking ring is screwed in, first you need to check the correct installation of the cassette and only after that you can finally tighten it. Tightens the retaining ring clockwise.

Removing and installing the cassette is not difficult, because with a minimum set of tools and at least basic knowledge of the technical plan, all the work will take a little time, a maximum of 60 minutes. But even if such a process is to be carried out for the first time, you should not give up. the experience of removing and installing a cassette will certainly come in handy more than once. The fact is that experienced cyclists recommend carrying out such maintenance of the bicycle cassette at least once a year.

Change the sprockets on the rear wheel of the bike

The drivetrain plays a very important role in the operation of the entire bike, so you must carefully monitor the wear of its individual parts. This is especially true of the rear wheel sprockets, which fail over time. A worn sprocket must be replaced as soon as possible, and it will not be difficult to do this.

Required set of tools

Before starting the replacement process, get yourself the tools you need to use. It:

  • Whip
  • Cassette remover
  • Rozhkova and adjustable wrenches

How to properly disassemble a cassette?

First, remove the rear wheel from the bike. This is very easy to do. Unscrew the nut with a wrench and release the chain. Owners of mountain models just need to press on the special mount and the wheel will be dismantled. Next, we install a removable device on the slotted nut of the cassette. Here we need a whip that will prevent the cassette from turning. While we rotate the puller with an adjustable wrench, hold the largest star with a whip.

The process of dismantling and replacing the sprocket

Using the nut, unscrew the cassette and remove it from the wheel. We carefully examine the stars and determine which one has become unusable. Start with the smallest and end with the largest. The bike drivetrain is designed in such a way that you can only replace the worn out sprockets and not the entire cassette. Therefore, after examining the cassette, you remove the used parts from it and replace them with new ones. It is very easy to pull the star out of the cassette, this is facilitated by special rivets. The main thing is to carefully remember the order of the stars, so as not to get confused with their installation back. In the configuration of some bikes, you may find so-called “spiders”. It is a group of several stars that are inextricably linked. In this case, you will have to replace the entire spider. Many cyclists face the following problem. After replacing several stars, there is a great discomfort in the operation of the chain. This is due to the fact that the chain has already passed a certain mileage, has worn out and now it is difficult for it to interact with new parts. Therefore, experts recommend the simultaneous replacement of the chain and worn sprockets. This greatly minimizes the complexity of your bike’s drivetrain.

What You Should Know About Singlespeed?

If you own a single speed bike, the process of replacing the chainring will be simplified to a minimum. You just need to open the retaining ring. If your own ring has become unusable, it must be replaced immediately, even if you are not going to replace the stars in the near future. Otherwise, the chain will lose its fixation, and this threatens with backlash. The process of replacing the ring is very simple, you do not need to perform the slightest forceful manipulations. Therefore, if you are talking about a single-speed bike, everything is very easy and understandable here. However, owners of such models should carry out the process of dismantling the cassette only if one or more of the largest stars have worn out. If a small asterisk begins to fail, this is not a cause for concern. Whatever you ride, remember that both the simplest road bike and the super-fast bike need a proper transmission. A badly worn chain and stars will not allow you to drive even a couple of meters. Pay close attention to the mechanics and timely replace worn-out parts. A working bike is the main guarantee of your safety and a cool, trouble-free ride!

Removing the chain from a bike

Two-wheeled vehicle repair skills will help riders deal with difficult issues quickly and efficiently. The most frequently asked question is how to remove the chain from the bicycle. At any time, unforeseen situations or the need for maintenance of equipment may arise and therefore several recommendations will help.

When is it necessary?

This procedure may be needed at the following points:

  • Replacing an old part with a new one;
  • Installation of new speed switches on the transport;
  • To make the chain shorter;
  • To clean the element.

Work process

Removing an element with a lock does not take much time and effort. Today there are several varieties of this bicycle chain device, but the principle of their opening is similar. It is necessary to close the axles and remove the cover. For convenience, you can use pliers, it is also good if you have a pliers for opening at hand. Thus, the whole procedure does not take much time and you can quickly remove the malfunction, change the part or remove the chain from the bike.

If there is no lock, then you need to make some effort. For work, you need a special squeeze. It is a tool with which it is very convenient and easy to extrude a pin. To work, you must position the chain link so that the release axle is directly opposite the pin. Then you need to twist the handle and squeeze out the pin itself. It is very important not to allow it to pop out, otherwise it will be very difficult to insert the pin into place correctly. Further, the bicycle chain can be replaced or repaired.

There are also some points to consider when working. For example, there was repeated removal of the same bicycle chain, then the next time it is necessary to open another link and segment, because after this process it loosens a little. Also, some models of pomace may have two seats and you need to fasten the link carefully, correctly and carefully.

Design and its features

A bicycle chain is a fairly simple metal structure that is designed to transfer the drivetrain from the drive sprocket to the driven one. Constituent elements:

  • Outer plate;
  • Inner plate;
  • Pin (roller);
  • Roller;
  • Sleeve.

The main difference between the different types is the distance between the rollers and the width. In some modes of transport, this part may be part of the gearshift system. This detail is important and requires special attention.

A bicycle chain requires regular maintenance, cleaning and repair to function properly. Regular lubrication and flushing will ensure that the equipment works well, and every few thousand kilometers the chain must be replaced with a new one. There is also a certain indicator of the degree of elongation (0.5%), that is, pores when a new part is needed. Without special measuring tools, you can determine the degree of wear as follows: you need to install the element on the largest sprocket (leading) and pull it off, moving it away from the teeth. If more than 4 teeth fit into the resulting space, then the bicycle part must be urgently replaced.

Change the sprockets on the rear wheel of the bike

The drivetrain plays a very important role in the operation of the entire bike, so you must carefully monitor the wear of its individual parts. This is especially true of the rear wheel sprockets, which fail over time. A worn sprocket must be replaced as soon as possible, and it will not be difficult to do this.

Required set of tools

Before starting the replacement process, get yourself the tools you need to use. It:

  • Whip
  • Cassette remover
  • Rozhkova and adjustable wrenches

How to properly disassemble a cassette?

First, remove the rear wheel from the bike. This is very easy to do. Unscrew the nut with a wrench and release the chain. Owners of mountain models just need to press on the special mount and the wheel will be dismantled. Next, we install a removable device on the slotted nut of the cassette. Here we need a whip that will prevent the cassette from turning. While we rotate the puller with an adjustable wrench, hold the largest star with a whip.

The process of dismantling and replacing the sprocket

Using the nut, unscrew the cassette and remove it from the wheel. We carefully examine the stars and determine which one has become unusable. Start with the smallest and end with the largest. The bike drivetrain is designed in such a way that you can only replace the worn out sprockets and not the entire cassette. Therefore, after examining the cassette, you remove the used parts from it and replace them with new ones. It is very easy to pull the star out of the cassette, this is facilitated by special rivets. The main thing is to carefully remember the order of the stars, so as not to get confused with their installation back. In the configuration of some bikes, you may find so-called “spiders”. It is a group of several stars that are inextricably linked. In this case, you will have to replace the entire spider. Many cyclists face the following problem. After replacing several stars, there is a great discomfort in the operation of the chain. This is due to the fact that the chain has already passed a certain mileage, has worn out and now it is difficult for it to interact with new parts. Therefore, experts recommend the simultaneous replacement of the chain and worn sprockets. This greatly minimizes the complexity of your bike‘s drivetrain.

What You Should Know About Singlespeed?

If you own a single speed bike, the process of replacing the chainring will be simplified to a minimum. You just need to open the retaining ring. If your own ring has become unusable, it must be replaced immediately, even if you are not going to replace the stars in the near future. Otherwise, the chain will lose its fixation, and this threatens with backlash. The process of replacing the ring is very simple, you do not need to perform the slightest forceful manipulations. Therefore, if you are talking about a single-speed bike, everything is very easy and understandable here. However, owners of such models should carry out the process of dismantling the cassette only if one or more of the largest stars have worn out. If a small asterisk begins to fail, this is not a cause for concern. Whatever you ride, remember that both the simplest road bike and the super-fast bike need a proper transmission. A badly worn chain and stars will not allow you to drive even a couple of meters. Pay close attention to the mechanics and timely replace worn-out parts. A working bike is the main guarantee of your safety and a cool, trouble-free ride!

Table of Contents