How to remove the pedals of a stealth 510 bike

Variety of pedals

Depending on the platform, the pedals are divided into:

remove, pedals, stealth, bike

How to remove and replace pedals on a bicycle

A situation has arisen that it is necessary to unscrew the pedals from the bike, but you do not know how to do it correctly. Let’s take a look at how to perform this operation quickly and easily.

How to change pedals on a bike

The bicycle pedal, as an integral part of the crankset design, is a fairly simple part in itself, but it is thanks to it that the bicycle wheels are set in motion. Due to the high stress on the pedals, special attention must be paid to them.

During the operation of the bicycle, one should not forget about regular maintenance of the pedals, which, as a rule, includes: inspection for cracks, chips, play, moisture or sand, etc., as well as cleaning and lubricating the threads of the axle and the connecting rod itself.

If the pedal for any reason is out of order and needs to be repaired (serviced) or replaced, the bike owner will have to deal with some of the features of its dismantling.

First, let’s get acquainted with the design of pedals, their types, and consider what tools should be prepared before work.

Required tools and materials

Before removing the pedals, it is necessary to prepare the tool and auxiliary materials that are most likely to be needed.

  • lubrication. it is recommended to clean and lubricate the removed parts;
  • cleaning rags;
  • kerosene or solvent. in case the axles do not unscrew or there are large contaminated areas.
  • an adjustable wrench is a universal solution, a small one is desirable, otherwise it will be difficult to get to the nut;
  • open-end wrench for 15. fits almost all models;
  • bicycle kit. in case of emergency;
  • pedal wrench. supplied by manufacturers for non-standard nuts and just in sets;
  • puller. addition to the foot pedals. a standard tool, often supplied by the manufacturer, serves to hold the axle when turning to the side with a wrench.

Removing bicycle pedals

When starting to dismantle the pedal, it is important to remember that the thread on bicycle pedals is different, namely: the axis of the left pedal has a left thread, therefore it is unscrewed clockwise, and right. right and unscrewed counterclockwise.

Removal process for conventional pedals:

  • To begin with, the system slides in the direction of the steering wheel, and then the pedals are gently unscrewed from the crank.
  • Remove the plug located at the end of the platform, thereby opening the lock nut.
  • We unscrew the lock nut, while holding the axle at the connecting rod with the second key.
  • Remove the lock washer located at the end.
  • Unscrew the cone.
  • Removing the platform from the axle, do not forget about the bearings. Better to shoot them separately. If they are loose, then you should put a rag or sheet so that the balls do not roll in different directions.

The process of removing the clipless pedals:

  • On the pedal in the place indicated by the arrow (see figure), fix the puller and unscrew.
  • Removing the axle from the pedal body without much effort.
  • Unscrew the lock nut securing the entire axial structure. To do this, you need to hold the axis itself with a key, or clamp it in a vice.
  • We take out all the nodes in order. At the same time, do not forget about the bearings and make sure that they do not scatter.

For reference: on each side, their quantity is 12 pieces.

Important! Due to the constant influence of the environment and the serious mechanical stress to which the pedal is subjected, some difficulties may arise when twisting this unit. Experienced cyclists use two techniques to make it easier to remove the pedals:

  • The bicycle pedal can be soaked in solvent or kerosene to get rid of any clogged dirt blocking rotation as much as possible.
  • The connecting rod and axle can be heated: slight deformation will loosen the threads and help remove the axle.

It is also important in the process of installing the pedal, while twisting the axle, not to damage the thread, because this will significantly complicate the subsequent removal process. Everything needs to be done as carefully as possible.!

When you may need to remove bike pedals

The peculiarity of the pedals is that they have symmetrical threads.

Each of them must have a label: which is left and which is right. Usually these are the English letters L. Left (left) and R –Right (right), respectively, for the left and right pedals.

READ  How to inflate a bicycle wheel without a pump

The left pedal is always made with a left hand thread. This means that it twists counterclockwise and unscrews clockwise.

On the right, there is a regular right-hand thread. Twists clockwise and unscrews counterclockwise.

This is done so that when the pedals are spinning while the bike is moving, they do not unscrew.

It is easier to remember the rule: the pedals are unscrewed against the direction of the bicycle’s movement. twist to the rear wheel, and twist in the direction of travel. twist to the front wheel.

Required tools and supplies

When replacing, as in repairing (servicing) the pedal, you will most likely need the following materials: cleaning rags, thinner or kerosene and heavy grease.

Removing and disassembling bicycle pedals may require tools such as:

Bicycle “Stealth

The manufacturer attracts with serious equipment and carbon frames (StelsNavigator 890DCarbon). An amazing aspect is the attractive price-performance ratio.

Required tools and materials

Before removing the pedals, it is necessary to prepare the tool and auxiliary materials that are most likely to be needed.

  • lubrication. it is recommended to clean and lubricate the removed parts;
  • cleaning rags;
  • kerosene or solvent. in case the axles do not unscrew or there are large contaminated areas.
  • an adjustable wrench is a universal solution, a small one is desirable, otherwise it will be difficult to get to the nut;
  • open-end wrench for 15. fits almost all models;
  • bicycle kit. in case of emergency;
  • pedal wrench. supplied by manufacturers for non-standard nuts and just in sets;
  • puller. addition to the foot pedals. a standard tool, often supplied by the manufacturer, serves to hold the axle when turning to the side with a wrench.

Partial lubrication

If you are faced with a squeak, but there is no time for serious and thorough repairs, you can use partial lubrication.

How to Remove Exercise Bike Pedals

It will not eliminate the problem completely, but will only allow you to postpone its solution for a certain time.

Like pain pills, it will relieve pain, and when you have the opportunity, you will undergo a full course of treatment.

Any liquid lubricating oil will work for you. This method does not require unscrewing the pedal from the crank arm. Lay the bike on its side with the end of the pedal facing up. Remove the plug covering the hole where the bushing is located. A knife or screwdriver is suitable for this. Then slowly pour 2-3 ml of oil into the structure. In this case, you need to slowly rotate the pedal so that the lubricating fluid penetrates into the mechanism. Then replace the plug and quickly rotate the pedal again. Finally, lift the machine onto the wheels and rotate the part several times again.

This will help to get rid of unpleasant sensations during driving and difficulties in rotation for a certain period of time. However, pretty soon the oil will leak out, and the above symptoms will manifest themselves. Therefore, for a high-quality “treatment” of bicycle pedals, a complete disassembly of the mechanism will be required.

Disassembly of bike pedals

The main feature of disassembling the pedals is that they have different threads.

Therefore, the right pedal is unscrewed counterclockwise, and the left pedal clockwise.

To unscrew the pedal from the connecting rod, you need a 15 wrench that can crawl into the gap between these two parts.

After dismantling the pedal, disconnect the plug and unscrew the lock nut with a socket wrench. Then remove the washer and bearing cone.

The cone should be twisted carefully so as not to lose the balls. Pull out all the bearing balls and set them aside.

It is important not to overturn the pedal and support the axle, which can also fall out along with the elements of the second bearing.

It is better to count the balls in order to know the exact number of elements. After that, from the opposite side, you can directly pull out the axis.

Since the balls of the second bearing can be glued to it on the old grease, you need to be careful. It is advisable to perform an operation on some kind of rag so that the dropped balls do not roll away.

The balls of the first and second bearing should not be confused, so put them in different places to know the position of each individual element.

Having disassembled the structure, proceed to cleaning. You can remove old grease with ordinary rags and WD-40, which can soften the stuck grease without damaging the parts.

READ  How to ride a bike on the road

Pedal types

  • regular (platform);
  • contact;
  • combined.

Each of the pedal types has its own specifics: the first is created for any footwear, the contact type exists for grip with sports shoes and the universal third type, which has a platform on one side and a clutch mechanism on the other. The method of disassembly also depends on the type of part. The mechanism of conventional pedals is simpler and faster to disassemble.

How to remove pedals from a stealth bike

At first glance, the design of the pedal looks simple, but in order to dismantle it, you need to have certain knowledge and a set of tools.

Removing your bike pedals may be necessary for various reasons: before transporting your bike, for regular maintenance checks, or after storing it on your balcony before the season starts. There are situations when a part crunches or emits other atypical sounds, in which case it must either be cleaned or completely dismantled, replaced with a new one. Pedal assemblies of new vehicles often need additional adjustments for a specific person. Therefore, many have the question of how to unscrew the pedals on a bicycle.

How to disassemble a bicycle pedal if you have clipless pedals

Clip-on pedals are more complex and the rotation is tighter. Using an example, let’s look at the maintenance of the most common and cheapest contacts. Shimano PD-M520. If you do not have any problems with the pedals, then it is better not to disassemble them again, so as not to amass unnecessary problems. They do not require frequent maintenance.

They are removed from the connecting rods in the same way as conventional pedals. using a key. To remove the axle, you will need a special tool. a Shimano TL-PD40 crank puller, keys for 7, 10 and 15. For the older Shimano PD-M540 model, such a puller is not required.

  • We put the connecting rod puller on the pedal in the place indicated by the arrow and unscrew it. After that, we easily remove the axle from the pedal body.
  • Holding the axle with a wrench or holding it in a vice, unscrew the locknut that holds the entire axial structure. Then we take out all the nodes in order, but be careful, as there are balls inside. There should be 12 of them on each side.

The pedal is completely disassembled. Here we do everything the same way, carefully wipe the old grease from all pedal assemblies and grease it with waterproof grease. Putting it up in the reverse order. The balls must be laid out one by one on their seat, having previously lubricated with a thick layer of grease. It is important to tighten the nuts well at the same time so that the pedal rotates smoothly and without backlash. After the performed manipulations, remove all excess grease that may be released after tightening the pedal. The Shimano PD-M520 pedal diagram is presented below for a general representation of the constituent parts At the end I would like to remind you that pedals are subject to heavy stress and require special attention and care.

Watch another video on how to install the pedals on your bike correctly

How to lubricate pedals on a bicycle

After the manipulations done, all parts must be thoroughly wiped with a clean cloth. To facilitate the task, you can put all the pedal assemblies in kerosene, then wipe them. This will maximize the cleaning of old grease, sand and other things. Be sure to check the condition of the balls so that they are all the same shape and size.

Then grease all parts with heavy grease, it is recommended to grease with waterproof grease and then reassemble the pedal in the reverse order. Do not forget to wipe the axle thread cleanly and lubricate it with grease before installing the pedal, which will allow you to smoothly put the pedal in place. And next time the pedals will unscrew easily.


In the course of work, the following tools may come in handy:

  • Hand wrench. allows access to nuts and disassembly of connections.
  • Bicycle kit. acts as a one-stop solution for a variety of repair procedures.
  • Open-end wrench. suitable for removing pedals on almost all bike models.
  • Special wrench for the system. makes it possible to remove non-standard nuts.
  • Puller. indispensable when you need to work with contact pedals. Allows you to lock the axis when using a hand key.

What tool are pedals removed

When using an adjustable wrench, be sure to pay attention to its thickness. The fact is that the distance between the pedal mount and the connecting rod is not large, and not every adjustable wrench will fit there. Some types of wrenches come with thin jaws that can be used. Open-end wrenches or special pedal keys are great for this operation.

READ  How to DIY a 3 wheeled bike

Bike Hack. How to Remove Bike Pedals That Are Stuck

How to remove the pedal from the bike and replace the connecting rod

The pedal is a simple part, but the long life can cause some disassembly problems. Therefore, many experts recommend systematic maintenance of the vehicle, despite the fact that many do not attach importance to this issue.

Let us analyze in which cases it is necessary to remove the pedals:

  • the part is damaged and requires replacement;
  • lubricate the elements;
  • replacement or repair of the connecting rod;
  • you need to understand the features of the system and understand how it works.

Before removing the pedal from the bike, the following tools should be prepared:

  • open-end wrench 15;
  • adjustable wrench;
  • if there is a non-standard solution of the manufacturer in the fastening elements, then usually the set contains a key for removing the pedal.

Useful to pay attention

How To Fit & Remove Bike Pedals With Ease

Stages of work

Removing the pedals requires a fairly simple tool. wrench and hexagon. The latter may not be suitable for some types of equipment and you can use either a crank puller or a wrench. Often only an adjustable wrench is used. Before starting work, you should know that the right pedal axis is unscrewed in the opposite direction to the clockwise, and left. clockwise. Step-by-step instruction:

  • Using a screwdriver, remove the special plug from the end;
  • Then you need to hold the axis with a key and unscrew the nuts;
  • Next, disassemble the washer, unscrew the cone;
  • Remove the bearings very carefully;
  • It is necessary to remove the pedals from their axis.

How to remove pedals from a bike

Bicycle. it is the most affordable, fairly convenient and useful means of transportation. Many people are fond of riding two-wheeled vehicles, someone performs virtuoso stunts on BMX, but in any case, timely maintenance and repair of equipment plays an important role. This avoids many unforeseen problems. There are times when the question arises: how to remove the pedals from the bike? Going a little deeper into the intricacies of the design, you can effectively carry out vehicle repairs yourself. Thus, you can feel the technique as much as possible, customize it according to individual preferences and easily deal with unexpected breakdowns.

Pedal design features

Such a simple element as a bicycle pedal has its own nuances. Today there are three types of parts:

  • Platform;
  • Contact pedals on a bicycle;
  • Combined.

Each of them has its own specifics: the former are designed to adhere to any shoe, the latter. for special cycling shoes, and still others are universal and have a contact mechanism on one side and a platform on the other. Thus, the bicycle pedal provides a comfortable ride.

The design also includes a low-maintenance and maintenance-free connecting rod. In case of mechanical damage or problems, you just need to change the connecting rod to a new one. All the nuts that secure this part are very easy to unscrew. First you need to remove the pedals, disassemble the cone and, if necessary, lubricate the bearings. The repair is not difficult and does not take much time. In order to remove the connecting rod, you need a special puller or certain skills. This is quite efficient and fast, otherwise it will take a lot of time and effort to disassemble the structure. The connecting rod is held by a large bolt on the shaft, while driving, the place where they touch becomes dirty and it is very difficult to remove the connecting rod.

In order to avoid problems with the pedals of the equipment, it is necessary to regularly inspect and troubleshoot. Bearings are also of great importance. There are several types of them, but simple bulk and cartridge ones, which differ in weight and quality, are especially popular. Specialists give preference to functional and reliable parts. Is there a large assortment in the modern market of sports equipment and parts? and choosing and replacing suitable pedals for your bike is not difficult. Repair of this element is quite simple.