How to remove the front wheel of a speed bike

How to remove the rear wheel yourself

Removing a large rear wheel is no more difficult than removing a front wheel. To make the dismantling process easier, remove the chain from the axle and spread the brakes.

Reverse mounting follows the same principle as with the front. However, when installing the chain, make sure it is correctly positioned on the sprocket. Therefore, first you need to put on the chain, and then mount the wheel on the mount.

How to remove the rear wheel?

The rear wheel removal process is COMPLETELY the same as the front wheel removal process. You don’t even need to look at the equipment suspended from the back (you only have to remove the chain from the axle if it gets caught).

How to remove / install the front wheel from a bike

Removing / installing the front wheel on a bicycle is one of the simplest tasks a cyclist may need. Usually, the front wheel is removed for transport or storage of the bike, but there are also situations when you need to remove the wheel in order to glue the camera or change the tire.

How to remove the front wheel?

If you have disc brakes, the task is even easier, but remember to insert a spacer between the brake pads because during transportation or repairs, you may accidentally press the brake, the pads will compress and complicate the installation procedure, especially if the brakes are hydraulic.

In order to remove a wheel from a bicycle with rim brakes, you need to unfasten the pads or lower the front wheel.

To unfasten, disconnect the pads, you need to press them to the rim with your hands at the junction of the cable, and pull the arc so that it crawls out of the groove.

Unscrew, remove the wheel.

After you have dealt with the brakes, proceed to removal. The wheel can be attached to the fork in two ways:

1) With a bolt. then you need a spanner or spanner of the desired size (usually from 13 to 17 sizes, but most often 14 or 15 sizes). Bolted connection is now found on children, teenagers, and also cheap bicycles.

2) Quick release. eccentric connection. Most common these days. Removal / installation of the wheel becomes possible even without the use of special tools. To remove the wheel, simply move the position of the eccentric clamp to the opposite side and hold it with your hand, make a couple of turns of the thumbscrew until you feel that the wheel moves easily.

The installation process is the opposite of removing.

remove, front, wheel, bike

How to Remove the Front Wheel on a Road Bike

1) Be sure to check the direction of the rubber when installing (compare with the rear wheel).

2) Do not pinch the eccentric when you press the eccentric handle, it should lower without much effort, but also check that the wheel does not wobble.

3) Check the center of the wheel, rotate it several times and apply the front brake, the wheel should not rub against the pads.

  • Your town:
  • Request a call
  • Turnkey hall
  • Veloremont
  • Guarantee
  • Payment
  • Delivery
  • Contacts

Some novice cyclists ask the question of how to remove a wheel from a bicycle. over, difficulties arise, as a rule, with the rear wheel. Quite often you can hear such phrases: “Oh, I’m afraid to take off the rear wheel, there are so many things screwed up, screwed up, I will never put it back on and I will definitely break something. I’ll go to the service center.” Of course, you can do this, but than repeatedly spending your time and money for going to bicycle repair, it is easier to just figure out how to do this operation on your own, especially since such a need may arise somewhere in the forest outside the city, and a bicycle workshop there it will definitely not be found.

READ  How to set up hydraulic brakes on a tektro bike

Installing the front wheel

As you perfectly understand, the process of installing the front wheel is the opposite of removing it and it makes no sense to describe it in detail.

We put the wheel back, as it was. Do not confuse the direction of rotation of the wheel (written on the tire). Remember that your bike is overturned and it is worth considering the direction of travel. In the case of disc brakes, it is difficult to confuse, since it is necessary that the disc hits exactly between the pads.

We tighten the nuts or tighten the eccentric

If you have rim brakes, you need to return them to their original condition. We check that the wheel does not dangle, turns freely and the brake functions, otherwise we check everything again point by point.

How to remove the front wheel of a bicycle

The procedure here depends on the type of brakes used on your bike. If the brakes are disc type, then nothing can be removed. The rim brakes must first be released in order to be able to continue dismantling without hindrance. To make it easier to release the brakes, pull out the arch connecting the pads. Further, to remove the front wheel, proceed as follows:

  • Turn the bike upside down. Do this carefully so that it fits over the seat and steering wheel. There are many fragile devices on the steering wheel that can be easily damaged. This is a bell, headlights, accelerometers. Place a soft cloth under the derailleur of your bike to avoid scratching the part. If you are using a hydraulic system with brake fluid, do not keep the bike upside-down for long periods of time. This is fraught with air entering the tubes and subsequent bleeding of the brakes. This work cannot be called too laborious, but it will require additional time expenditures;
  • Remove the wheel. If it is secured with a nut, then unscrew it until the hub axle comes out of the mount freely. The eccentric fastening does not require any additional tools and devices for dismantling. Eccentric bindings are often found on sport and mountain bikes;
  • Finish dismantling.

Important! Do not use hydraulic disc brakes without a rotor between the pads as they can compress and jam. That will complicate the process of re-installation, up to the possible need to bleed the brakes. Therefore, take care of some kind of temporary spacer between the pads in advance.

When do you need to remove a bicycle wheel

Removing wheels may be required if you have such problems.

  • Significant damage to the rim;
  • Tube damage, tire rupture;
  • Knitting and balancing;
  • Bulkhead bushing;
  • Replacing the bike chain, rear sprockets.

As for the tools, a spanner of a suitable size is sufficient: open-end or ring-shaped. It is undesirable to use an adjustable wrench, since it licks off the corners of the nuts, due to insufficient snug fit.

No additional tools are needed to deal with the eccentric fastening.

Any cyclist has to deal with one or another malfunction of a bike in one way or another. Despite the simplicity of the manipulations, the first removal and replacement of a wheel, as a rule, takes a lot of time. In the future, with practice, the bulkhead, dismantling and installation will take literally minutes.

When do you need to remove a bicycle wheel?

Removing wheels may be required if you have such problems.

For tools, a suitable size open-end wrench or a ring spanner is sufficient. It is undesirable to use an adjustable wrench, since it licks off the corners of the nuts, due to insufficient snug fit.

No additional tools are needed to deal with the eccentric fastening.

Removing the front wheel from a bike

Any experienced cyclist knows how to remove a bicycle wheel on his own. This action often has to be done when a wheel needs to be repaired, replaced with a tire, rim or spokes, or simply replaced with another, more reliable or new wheel.

However, on newer bikes with different derailleurs and many parts, it is very difficult to change the wheel for a beginner who can do something wrong and panic.

Let’s figure out how to remove the front and rear wheel of a bicycle on our own, together.

Installing the front wheel

As you perfectly understand, the process of installing the front wheel is the opposite of removing it and it makes no sense to describe it in detail.

We put the wheel back, as it was. Do not confuse the direction of rotation of the wheel (written on the tire). Remember that your bike is overturned and it is worth considering the direction of travel. In the case of disc brakes, it is difficult to confuse, since it is necessary that the disc hits exactly between the pads.

READ  26 Wheels Per Bike

We tighten the nuts or tighten the eccentric

If you have rim brakes, you need to return them to their original condition. We check that the wheel does not dangle, turns freely and the brake functions, otherwise we check everything again point by point.

How to remove the front wheel of a bicycle

The procedure here depends on the type of brakes used on your bike. If the brakes are disc type, then nothing can be removed. The rim brakes must first be released in order to be able to continue dismantling without hindrance. To make it easier to release the brakes, pull out the arch connecting the pads. Further, to remove the front wheel, proceed as follows:

  • Turn the bike upside down. Do this carefully so that it fits over the seat and steering wheel. There are many fragile devices on the steering wheel that can be easily damaged. This is a bell, headlights, accelerometers. Place a soft cloth under the derailleur of your bike to avoid scratching the part. If you are using a hydraulic system with brake fluid, do not keep the bike upside-down for long periods of time. This is fraught with air entering the tubes and subsequent bleeding of the brakes. This work cannot be called too laborious, but it will require additional time expenditures;
  • Remove the wheel. If it is secured with a nut, then unscrew it until the hub axle comes out of the mount freely. The eccentric fastening does not require any additional tools and devices for dismantling. Eccentric bindings are often found on sport and mountain bikes;
  • Finish dismantling.

Important! Do not use hydraulic disc brakes without a rotor between the pads as they can compress and jam. That will complicate the process of re-installation, up to the possible need to bleed the brakes. Therefore, take care of some kind of temporary spacer between the pads in advance.

How to Remove Front Wheel from Your Bicycle. Disk Brake with Thru Axle

How to put the rear wheel back

Replacing the rear wheel is done in the same way as installing the front wheel. However, when fitting the wheel, it is important that the chain fits correctly onto the sprocket. Therefore, first we put the chain on the sprocket and then we put the wheel on the mount. It is better to do this with gloves, because the chain will get your hands dirty and you will have to wash them for a long time.

If you suddenly think that the chain is twisted or tangled on the sprockets, then you do not need to remove the wheel again. It is enough to twist the chain back and forth with the pedals or by hand to make it lock into place. You can also move the gearshift mechanism, which is located in the chain mechanism, and then put on the released chain as you like.

If you have any difficulties in disassembling a bike, then you can read our article How to disassemble a bike.

SRC: How To Remove Your Front Wheel On Your Bicycle

You can also read our article How to inflate a wheel.

If you have never done something, then you may think that it is difficult to do it. If you have never removed the wheels from a bicycle before, then you may also be afraid that you will not cope, especially with the rear wheel (after all, there is a chain, a bunch of stars and this tricky derailleur!). But now we will tell you everything about this simple operation. There is nothing supernatural here. In short, we have already touched on this issue in the article on how to disassemble a bicycle, and now we will open this topic a little wider. You will have to remove the wheel not only if you need to disassemble the bike for transportation or storage, but also in order to replace the camera, tire or spokes (we will devote a separate article to what the wheels of a bicycle consist of), get rid of the figure eight.

How to remove wheels from a bicycle with rim brakes

If you have rim brakes, release them first. To do this, slide the brake levers towards each other and lift the cable lock up.

If you need to remove both wheels, release both brakes at once so that you don’t have to turn the bike over again. If you have tires with a large tread or they are large in diameter by themselves, then you will have to deflate a little air from the tubes. Now turn the bike upside down (if you have any accessories installed on your handlebars that can be damaged in this position, it is better to remove them in advance). The bike will stand stable enough for any operation, but if you have hydraulic brakes, it is better not to leave it in this position for a long time. air can get into the hydraulic line, which will entail a not very difficult, but tedious and time-consuming process of bleeding the brakes.

READ  How to adjust the brakes on a speed bike

How to remove the rear wheel of a bike

If you will be removing the rear wheel, then to make it easier to do, loosen the chain as much as possible by switching it to the smallest sprockets.

How to remove wheels from a bicycle with disc brakes

If you have disc brakes, just in case, insert something into the pads, in the slot where the disc was: if they accidentally close, it is very difficult to release them. And if you don’t open it, don’t put the wheel on. The role of something can be, for example, a piece of paper folded several times. And sometimes new bicycles come with a special plastic plug.

The assembly is carried out upside-down. To make it easier with the rear wheel, bring it to the attachment point, put the chain over the sprocket and after that insert the axle into place. Make sure the axle fits into the groove all the way and symmetrically. Are you convinced that there are no difficulties in installing the wheels on the bike? But there is one caveat: in order for the protector to work as it should, it must be oriented in the right direction. For the convenience of orientation, an arrow is drawn on the tire. in this direction the wheel rotates when the bicycle moves. But the fact that the bike is upside down when installing the wheels can be misleading. Therefore, take your time. This does not apply to the owners of bikes with disc brakes. it is impossible to confuse here. Do not over-tighten the eccentric; put the brakes back in place. Everything.

How to remove the rear wheel

Removing the rear wheel is as easy as removing the front. However, before removing the rear wheel from the mounts, you must first remove the chain from the axle, and also open the brakes so that they do not interfere.

How to reinstall the front wheel of a bicycle

Here, the same actions appear as in the case of withdrawal, only the order of actions is reversed.

  • Slide the bike wheel into the mount so as not to mix up the rotation. Information about the direction of rotation is on the tire, but you must remember that the bike is still upside down. This is important, otherwise eights may appear on the rim;
  • Secure the axles with an eccentric or nut. Check the tightness of the fastening so that the wheel cannot fly off while driving;
  • Turn the bike over;
  • Return the brakes to their original place (in the case of rim brakes).

At the end of all the manipulations, check the performance of the hero of the occasion and the correct operation of the brakes.

How to remove the front wheel of a bicycle

Before removing a wheel, you need to see what kind of brakes you have. If disc, then you can immediately proceed to removing the wheel. If the brakes are rim brakes, then you must first release them to make it easier to remove the wheel. Every rim brake manufacturer has almost the same removal. It is enough to pull out the arc that connects the two pads, so the brakes can be released. And for this you need the upper arc, which holds the pads together, press them together and unscrew the screw that holds the wire arc.

remove, front, wheel, bike

After that, we move on to removing the front wheel. For this:

It is important to remember that if you press the rim brakes without a wheel, it will compress the brakes and make it impossible to put the wheel back. Then you have to adjust the brakes again. But if you originally detached the rim brake arch, then compression will not occur.