How to Remove Speed ​​Bike Pedal Sprocket

How to change sprockets on a bike?

The bicycle is becoming more and more popular nowadays. This is due either to paid parking and the high cost of gasoline, or to the currently fashionable healthy lifestyle.

remove, speed, bike, pedal, sprocket

But almost everyone loves to ride a bike, but not everyone knows how to properly care for it. Naturally, over time, parts fail and they should be replaced with new ones or serviced.

How To Remove A Crank Set

Within the framework of this article, we will talk about bicycle sprockets and how you can disassemble and care for them.

Disassembly process of the transmission cassette

Some theory beforehand. On the rear wheel there can be two variants of parts related to gear shifting.

  • Transmission cassette. This product features modernity and innovative spline mountings that attach to the hub axle.
  • Ratchet. A somewhat outdated model typical of inexpensive speed bikes. There are no more than seven gears in a set. As for the mount, it has a thread with external installation parameters.

Let’s focus on the ratchet right away. Changing the rear sprocket on a ratchet bike is not possible. Only change the entire component completely.

Therefore, the topic of the article will be a problem describing a situation when a bicycle cassette star needs to be replaced. As for the set of stars in the transmission, up to 11 pieces are possible, depending on the bike model.

Remove Cranks Without A Crank Puller

So how do you change the rear sprocket on a speed bike? Consider the algorithm of actions.

  • Take the bicycle wrench for the rear wheel and dismantle it. We sequentially unclench the levers and loosen the fixing of the nut.
  • Now it is the turn for the axle nuts. Using another key, turn off the mount.
  • The next step involves unscrewing the bearing cone and pulling it out.
  • We take out the axis with all the elements.
  • We take a special tool. a cassette remover. We insert it into the slots.
  • The whip is placed on the largest sprocket. We make rotational movements clockwise.
  • At the same time, using an adjustable wrench, the puller rotates in the opposite direction.

Crankset Removal & Installation. Bike

The preliminary stage is over. Such simple actions are possible in ordinary household conditions. We emphasize that if more than one star is worn out, but several, then it is better to replace the entire cassette at once. This option is also desirable when the largest star is damaged.

And one more recommendation. We put all small parts, washers and nuts in a certain place, so that later we do not search all over the room

Star stripping process

How to change the rear sprocket on a bike after the first stage has already been passed.

  • Removing the mount.
  • Detach the cassette from the rear wheel.
  • We make a thorough inspection.
  • Determining Wear Sprockets.
  • We remove the worn out product.
  • Pay attention to the arrangement of the stars and the sequence of fasteners and washers between them.

Cassettes compare favorably with ratchets in that each worn part can be freely removed separately.

A separate recommendation would be to replace the chain, which is also worn out, along with the sprocket.

Why you need to change sprockets on a bike?

The sprocket on a bicycle has one of the main roles that affect ride quality and speed. During the use of a two-wheeled vehicle, a load is exerted on all its component parts.

Replacing the sprockets is essential for proper function and gear shifting. If you do not repair parts immediately after damage, there is such an option that broken parts will accumulate and repair will be quite costly, in some situations it exceeds the cost of the bike itself.

Bicycle sprocket design

The mechanism externally has several stars of different sizes, which are fixed with a bushing. After that, everything is connected with a lock nut.

  • The usual version is that the stars are connected to each other by a plastic spacer;
  • Spider cassette. cassettes made in the form of stars, fixed on an aluminum frame;
  • On several spiders. devices that have a high cost and are usually installed on professional and expensive models. The appearance has 2 spiders, which are connected by sets of stars;
  • X-Dome is a monolithic system that connects the drum to the lid on the opposite side;
  • OpenGlide. Most Relevant for Road Bikes.
READ  Which side to go on the bike

How to remove sprockets from the rear wheel of a bicycle?

It is absolutely not difficult to disassemble the device for replacement, but you should be careful and have a couple of free hours in stock.

In some situations, the disassembler initially spends 15 minutes, and another person without the necessary skills can handle it in 1-2 hours.

That is why it is difficult to answer the question of how much time can be spent on a laborious process. In most, all stars have the same parsing method, since they have almost the same structure.

Helpful hints for parsing:

  • How the parts are removed, in this order they should be installed. This advice will help from confusion and waste of extra time that can be spent remembering where a certain detail came from;
  • After parsing, every detail needs to be inspected, perhaps it does not require replacement, but a banal cleaning is simply necessary.

How to remove a sprocket from a bike

The sprockets of a speed bike are the main parts of the gearshift system that provide the gear ratio of the drivetrain. According to the degree of influence, they are divided into leaders and followers. The first ones are located at the connecting rod pair and are called the system. The driven ones are located on the rear wheel hub and are divided into cassettes and ratchets by design.

Over time, the stars wear out, as a result of which they need to be completely or partially replaced. The second option is more common in practice, since the wear is uneven. The most frequently used transmissions are subject to it. The problem, of course, requires a timely solution, otherwise driving will turn into torment. The chain will seize or skip worn stars. Many modern models allow you to remove the sprocket and put it separately on the system or cassette without replacing the entire assembly. Read on how to do this.

Stages of installing new stars

How does assembly work when replacing a bicycle cassette chainring?

  • Install a new sprocket and fix it.
  • We assemble the cassette completely in the reverse order.
  • Using a puller, mount the drum to the slotted area.
  • The drum must first be leveled.
  • Next, we carry out the process of assembling the bushing. All actions described in the first paragraph are carried out in reverse order.
  • Install the rear wheel and fix it securely.
  • Put on the chain.

It is imperative to check the smooth operation of the transmission. This procedure involves adjusting the rear derailleur.

If everything is carried out according to the proposed instructions, feel free to get on the bike and enjoy the ride.

How to remove sprockets from the rear wheel of a bicycle?

It is absolutely not difficult to disassemble the device for replacement, but you should be careful and have a couple of free hours in stock.

In some situations, the disassembler initially spends 15 minutes, and another person without the necessary skills can handle it in 1-2 hours.

That is why it is difficult to answer the question of how much time can be spent on a laborious process. In most, all stars have the same parsing method, since they have almost the same structure.

Helpful hints for parsing:

  • How the parts are removed, in this order they should be installed. This advice will help from confusion and waste of extra time that can be spent remembering where a certain detail came from;
  • After parsing, every detail needs to be inspected, perhaps it does not require replacement, but a banal cleaning is simply necessary.

How to replace a sprocket on a bike?

Replacing the sprocket should start with removing the old one, respectively, only then start the installation. If an old part is installed, it must be cleaned and lubricated, only then install.

  • We put on a protective plastic ring;
  • If the stars themselves are not fastened to each other, then they should be worn one at a time, starting with a large one and ending with a small one. We install small rubber pads between the stars;
  • We screw it with a nut, this must be done directly with a wrench. Twisting is carried out according to the hour hands;
  • We fix the nut and check the movement of the nut.

Change the sprocket on the rear cassette

The set of transmission stars of the rear wheel is several times larger than the front one. The standard kit includes eight components, and in high-speed models (or on a sports bike) there are 9 or 11.

It is worth mentioning right away that a cassette or ratchet can be placed behind. The cassette is a modern version with an internal splined mounting on the hub axle. Ratchets, as an outdated option, can only be found on a budget high-speed bike. The set usually includes 5-7 gears. External mount, threaded, removable tool differs from cassette.

The fundamental difference from the cassette is its integrity. it is impossible to change the star separately on the ratchet. Here, either all at once, or nothing at all. Therefore, we will consider how to install a new sprocket on the cassette.

READ  DIY ceiling bike suspension

As with replacing the leading stars, special tools are required here:

  • cassette remover;
  • chain whip-retainer;
  • adjustable wrench or head;
  • optional: wrenches, chain release.

When removing the cassette, you will need to first remove the rear wheel from the bike and then the axle nuts. At the same time, when replacing the sprockets, you can also clean the chain. to remove it, you need a squeeze.

Sequence of work: 1. Remove the rear wheel with a 15 wrench, with eccentric fastening everything is simple. unclench the lever and loosen the fixing nut.

The next step is to unscrew the axle nuts. You will need a 17 key for it. To roll the mount off the rotating axle, we put on an additional nut to fix the axle.

Unscrew the bearing cone and pull out the bearing from the opposite side.

Remove axle with taper and bearing. About the bushing components: if necessary, you can immediately replace them with new ones.

Place the whip on the largest (lowest) star. We will rotate it clockwise.

Use an adjustable wrench or a head to turn the puller counterclockwise.

It is so easy to shoot a cassette at home. Most modern star sets are collapsible, you can install one or two new stars. However, in case of severe wear, when half of the cassette is worn off, it makes no sense to change them separately. Difficulties can also arise if the largest sprocket has been erased, on which all the others are usually attached.

Is it possible to dismantle a cassette without a puller and a whip? In principle, this can be done with a slotted tube and a spanner. The whip can be made by yourself by welding a piece of an old chain to the metal handle of the knife.

When replacing individual stars, especially the middle ones, we disassemble the cassette carefully so as not to lose all the spacer and fixing washers. Everything is easier with a cassette on a spider. it does not need to be disassembled, the star is removed separately from its mount.

Rear transmission assembly:

  • Put and fix a new star, assemble a cassette.
  • Using a puller, install the drum on the spline mount of the sleeve. Before tightening, the drum must be leveled so that the connection does not wear off under load. The whip is not needed here. just rotate the puller clockwise with effort.
  • Assemble the bushing: insert the axle from the side of the cassette, then the bearing and the cone on the left side, fix the axle with nuts.
  • Put on the chain and put on the rear wheel.

Check transmission operation and adjust rear derailleur. Timely replacement of sprockets will save you from unpleasant surprises on trips and will, in general, increase the resource of the bicycle transmission.

How to install a cassette on a bike

First of all, make sure that the cassette assembly matches the unfolded / removed parts. To facilitate this process, the sprockets have grooves of different sizes (for each sprocket. individual), and the bushing has suitable splines. It is the correct alignment of the grooves and splines that all the sprockets will stand in a certain order.

There are some important things to keep in mind when installing the cassette on your bike:

  • Many cyclists lubricate the bushing surface before installing the part in question. However, experts believe this is wrong. after lubrication (until the entire cassette is assembled and installed), both dust and dirt will have time to get onto the applied lubricant, which ultimately leads to the need for maintenance, repair or replacement of elements.
  • Experienced cyclists lubricate the thread of the retaining ring before assembling the cassette. during subsequent disassembly it will be much easier to unscrew.
  • All sprockets must be worn alternately, but do not forget to put spacer rings between them. In some bike models, you can see not separate sprockets, but a single / one-piece assembly.
  • In many bicycles, to securely install the last sprocket, you need to press it slightly and only then you can screw the retaining ring.
  • After the locking ring is screwed in, first you need to check the correct installation of the cassette and only then can it be finally tightened. Tightens the retaining ring clockwise.

Removing and installing the cassette is not difficult, because if you have a minimum set of tools and at least basic knowledge of the technical plan, all the work will take a little time, a maximum of 60 minutes. But even if such a process is to be carried out for the first time, you should not give up. the experience of removing and installing a cassette will certainly come in handy more than once. The fact is that experienced cyclists recommend carrying out such maintenance of the bicycle cassette at least once a year.

Bicycle sprocket design

The mechanism externally has several stars of different sizes, which are fixed with a bushing. After that, everything is connected with a lock nut.

  • The usual version is that the stars are connected to each other by a plastic spacer;
  • Spider cassette. cassettes made in the form of stars, fixed on an aluminum frame;
  • On several spiders. devices that have a high cost and are usually installed on professional and expensive models. The appearance has 2 spiders, which are connected by sets of stars;
  • X-Dome is a monolithic system that connects the drum to the lid on the opposite side;
  • Opengl
READ  How to make rear brakes on a bike

Materials and tools

To carry out the work, you will need tools:

Important! Do not use any tools or tools such as pliers, wire cutters and the like to remove the pedals. Will not help, but it will damage the pedal mounts and their coating.

  • The most suitable is a dedicated bicycle tool kit, which contains all the necessary accessories.
  • An adjustable or so-called small gas wrench will do.
  • Spanner, also known as an open-end wrench for 15.
  • Or a special pedal key.

Since the pedals interact quite closely with the environment, they can be covered with dirt or rust. For smooth maintenance and dismantling, all contamination must be removed. To do this, prepare:

  • Specific rust removers (e.g. WD-40).
  • Either a kerosene-containing liquid.
  • Cleaning cloth and cloth for laying out removed and washed pedals.
  • Plastic bags and containers for storing and washing removed pedals.

So, almost everything is ready to go. It remains to place the bike vertically. this can be done using special supports-stands or leaning it against a vertical surface. It is desirable that the wheels rest on the ground, which will provide stability and additional support.

Removing the right pedal

Getting started. first of all, you need to position yourself facing the pedal to be removed. In our case. facing the right side of the asterisk.

Important! Each pedal has its own thread. The right one must be unscrewed counterclockwise, the left one. clockwise. Some models are marked “R” and “L”. If there is no marking, it is advisable to lay the removed pedals so as not to confuse their location during subsequent installation.

The connecting rod with the pedal must be installed horizontally, pointing forward. or otherwise at the three o’clock position.

Place the wrench on the nut head and rotate it in the required direction.

Important! Do not apply great force when rotating and, moreover, do not use additional tools such as a hammer. If the nut does not rotate, it may have stuck, then use WD-40 fluid. Spray the nut and threads, wait five to ten minutes and repeat the procedure. If a special liquid is not at hand, then you can use the warming method. heat the junction with hot water (rags with boiling water) for several minutes (it is strongly not recommended to use burners or lighters!).

  • When removing, support the pedal with your free hand and be careful. A key that comes off can injure your hand. Take your time, careful use of tools will save you from possible troubles.
  • After unscrewing the nut, remove the pedal, pay attention to the presence of washers and gaskets. To prevent them from getting lost, put them in the prepared box.

Removing the left pedal

So, the right pedal is removed. The bike will now need to be positioned to provide access to the left pedal. Then we repeat all the above procedures, but with the difference that the connecting rod is installed horizontally forward or otherwise in the position “at nine o’clock”, and rotate the nut clockwise.

The pedals are off! What to do next? Further actions depend on the need:

  • If the pedals were removed for long-term storage or transportation of the bike, then it is necessary to pack them in plastic bags, it is highly advisable to put a bag of silica gel in bags to protect against moisture and rust.
  • If for maintenance, then the following is a description of this procedure.

The first case is transportation or long-term storage

When is it necessary to remove the pedals? Firstly, if you do not intend to use the bike for a long time, or if it needs to be prepared for transportation, it is better to remove the pedals and preserve them.

Pedal Removal Procedure

The mountain bike is on a stand, the pedals are cleaned from dirt, the tools are ready at hand, the cloth is spread out. everything is ready. A small note. some experts advise you to first remove the chain from the sprocket.

The second case is the need for repair or maintenance

The second, very unpleasant case. creaking, crunching, backlash, mechanical damage. here you cannot do without removal, inspection and maintenance.

It must be remembered that the pedal is a rather complex mechanism with moving parts that requires periodic maintenance, for which it must be dismantled.