How To Remove Pedals From A Stealth Bike

How to remove pedals from a stealth bike

How to unscrew the pedals on a bike

Bicycle pedals are the part of the crankset that propels the bike. Therefore, this unit is subject to heavy load and requires special attention.

Bicycle pedals are a fairly simple mechanism, but at the same time they consist of:

  • Here are the bicycle pedals. it is a metal pin, which has a thread at the end, with which it is screwed into the connecting rod,
  • Pedal platform. the surface that contacts the foot,
  • Bicycle pedal bearings. provide torque along the pedal axis,
  • Bolts, nuts, plugs
  • Read about why the pedals on the bike spin and what to do to avoid it in this article.
  • Contact bike pedals, folding pedals and other pedals can be found here.

Operation of the pedals in various weather conditions can lead to their failure, pedal axis backlash, crackling, crunching, knocking directly on the bicycle pedals may occur. All these problems are not difficult to fix. Therefore, if you notice that your pedals squeak on your bike, then in order to make the pedal more flexible, you will need to Unscrew and remove it from the bike.

Today we will look at how to disassemble a regular pedal and clipless pedals.

How to disassemble pedals on a bicycle

First, let’s look at the simplest pedal problems (crackling, crunching) that can arise:

Pedal repair. We tighten the lock nut

  • It is necessary to check if there is any damage to the pedal (cracks, chips, etc.),
  • Check the attachment point of the pedal axle to the connecting rods, over time it may weaken or moisture and sand may get into the connection. For prevention, you can Unscrew, carefully wipe the thread of the axle and the connecting rod itself, lubricate with thick grease and tighten again,
  • We check the pedal for backlash. To do this, hold down the pedals and try to move the platform in different directions with our hands. If there is play, then this is corrected. Tightening the locknut, which is located under the plug (see Figure)
  • If the pedal is spinning tightly or there is play, it is advisable to completely go over the bicycle pedal. It won’t take you a lot of time. Let’s get started:
  • Only an adjustable wrench is required to remove the pedals from the bicycle crank.

Important. It should be remembered that bicycle pedal threads are different. And if you do not remember which way the pedals are unscrewed.Reminder: here the right pedal has a right-hand thread and unscrews counterclockwise, and the left one. respectively, left and unscrews, as you already understood, clockwise.

Here the pedal usually has several edges, which allows you to unscrew it without much effort.

  • Remove the pedal cover with a screwdriver, which is located at the end,
  • Unscrew the lock nut, while holding it here with the key,
  • Removes the lock washer,
  • Unscrew the cone,
  • We take out the bearings (Be careful, as the balls can roll in different directions)
  • Removes the pedal platform from the wasp.
  • Everything, the pedal is completely disassembled. The process of removing and repairing the pedal will be faster if you use the repair stand. How to lubricate pedals on a bicycle

    • Learn also how to lubricate bicycle pedals

    After the performed manipulations, all parts must be thoroughly wiped with a clean cloth. To facilitate the task, you can put all the pedal assemblies in kerosene, then wipe them. This will allow you to clean up as much as possible of old grease, sand and other things. Be sure to check the condition of the balls so that they are all the same shape and size.

    Then grease all parts with heavy grease, it is recommended to grease the waterproof grease and then reassemble the pedal in the reverse order. Do not forget to wipe the axle thread cleanly before installing the pedal and lubricate it with grease, which will allow you to smoothly put the pedal in place. And next time the pedals will unscrew easily.

    How to disassemble a bicycle pedal if you have clipless pedals

    • Also learn about correct pedaling technique, which may help to avoid many pedaling problems.

    Clip-on pedals are more complex and rotate tighter. For example, let’s look at the maintenance of the most common and cheapest contacts. Shimano PD-M520. If you have any problems with the pedals, then it is better not to disassemble them again, so as not to amass unnecessary problems. They do NOT require frequent maintenance.

    They can be removed from the connecting rods in the same way as conventional pedals. using a key. To remove the axle, you will need a special tool. a Shimano TL-PD40 crank puller, keys for 7, 10 and 15. For the older Shimano PD-M540 model, such a puller is NOT required.

    To unscrew the bicycle pedal, you need a special puller

    • We put the connecting rod puller on the pedal in the place indicated by the arrow and unscrew it. After that, we easily take it out from the pedal body.
    • Holding here with a key or clamped in a vice, unscrew the lock nut that holds the entire axial structure. Then we take out all the nodes in order, but be careful, as there are balls inside. There should be 12 of them on each side.

    The pedal is completely disassembled. Do everything here the same way, carefully wipe the old grease from all pedal assemblies and grease the waterproof grease. Putting it up in the reverse order. The balls must be laid out one at a time on their seat, having previously lubricated with a thick layer of grease. It is important to tighten the nuts well at the same time so that the pedal rotates smoothly and without backlash. After the performed manipulations, remove all excess grease that may be released after tightening the pedal.
    The Shimano PD-M520 pedal diagram is shown below for an overview of the component parts.

    General diagram of the bicycle pedal disassembly

    In the end, I would like to remind you that pedals are subject to great stress and require special attention and careful attitude. If you want to know more about a bicycle bottom bracket, read here.

    Dismantling technology

    • Before starting the process, sprinkle the mating point of the connecting rod and the shaft with a magic solution of WD-40. It will dissolve the remaining dirt and make the process easier. You can just as well use BSK brake fluid if it is lying around in your garage. You can do the same if the bolt does not loosen.
    • Important! Make sure that the puller rod is less than the diameter of the squares on which the connecting rod is fitted. Otherwise, the operation will fail. the thread will break.
    • Unscrew the mounting bolt.
    • We screw the puller into the connecting rod to the limit, making sure that the puller rod is unscrewed as much as possible.
    • We tighten the puller bolt smoothly and without jerking, otherwise there is a risk of damaging the thread.

    Here is a step-by-step photo instruction explaining the process visually.

    When is it necessary to dismantle the connecting rod

    The connecting rod does NOT require any maintenance or special care. Its replacement is carried out only in the case that we described above and in case of mechanical damage. The need for dismantling arises when we need to get to the carriage or completely disassemble it for lubrication, flushing or adjustments.

    Also, sometimes after the rain, an unpleasant creak occurs, which is caused by the ingress of sand into the connecting rod-shaft coupling. In this case, it has to be disassembled and cleaned.

    Puller application

    A special device that is designed to dismantle hard-to-remove parts is called a puller. This is a no brainer. In our case, to remove the connecting rod from the bicycle carriage shaft. It looks like this.

    READ  15 Bike Frame How Tall

    This type of connecting rod puller provides the ability to remove the pedal as well.

    The connecting rod is held on to the shaft by a heavy-duty 8mm head bolt. Unscrewing the bolt is NOT difficult. But the difficulty is that the connecting rod sits on the shaft with a slight tension and has a tapered fit. Very often, in wet weather, water and dirt penetrate into the interface between the connecting rod and the shaft. Then it sticks to the shaft and it is almost impossible to remove the connecting rod. But in our toolbox, of course, there is a puller for connecting rods, which is a complex turning part. a screw with a two-level head for an open-end wrench and a socket. A cunning nut with external and internal threads is screwed onto the screw. It takes a long time to explain, but in the photo everything is very clear.

    How to unscrew the bicycle crankset by yourself?

    Probably, no part of the bike has more load than the connecting rod. On the models of recent years of release, for their manufacture, instead of steel, various alloys began to be used. This makes the structure lighter and more robust. Sometimes, to reduce weight, the connecting rods are made hollow, they are also made of composite material, which somewhat increases the cost of the bike itself, but also greatly facilitates it.

    On inexpensive models of bicycles, a non-separable block of connecting rod-stars is made. Inconvenient and impractical option, because When replacing the sprockets, you will have to change both connecting rods at once. If you started to repair the carriage or replace the stars, then we recommend that you immediately replace both connecting rods with a design that assumes a detachable connecting rod and sprockets.

    Dismantling without puller

    In this case, scientific and technological progress offers few options.

    As you can see, we DO NOT get away from advanced technologies and progressive methods anywhere. Even in such a seemingly trifling matter.

    Carriage removal process for a beginner

    Undoubtedly, it is always difficult for a beginner in this or that business. But if there is a certain desire to do something with your own hands, then you need to learn and do. We present you with a description of how to remove the carriage from a bicycle with your own hands.

    Doing so-called maintenance of your own vehicle is better than trusting it to a stranger. After all, you will clearly know what works great in your device and what needs to be eliminated. If you have the necessary tools for various work with the bike, then you can carry out a number of actions yourself.

    In order to remove the carriage from the bike, as well as remove the pedals from the bike carriage, you need to prepare a number of tools that will be at your fingertips. These tools include:

    • A wrench for nuts or an adjustable character;
    • For connecting rods, a special squeeze is required;
    • Flat-type screwdriver;
    • A hammer, but small;
    • A tool that will allow you to remove the carriage itself.

    On a device such as a bicycle, the carriage is a bearing assembly. The main essence of such a mechanism is to connect the connecting rod to the frame. In addition, a product such as a carriage provides so-called torque to the connecting rods. Based on this, it can be understood that such a detail is very important on a bicycle, its condition affects a lot.

    The design of modern bicycles implies a special glass for such material as the carriage. This glass can be found in a specific area of ​​the rear pipe. As a rule, manufacturers install a carriage cup in the area of ​​the rear stays. Due to the fact that the device is installed in such a vulnerable area of ​​the bicycle, its durability is poor. From this it turns out that there is a need to check the device and repair it from time to time.

    It is negatively affected by dirt, dust and rain. For this reason, backlash is formed. If it does not clean on time and DO NOT prevent breakdowns of this product, then this threatens with a mass of negative nuances. During movement, you may encounter a decrease in potential speed or jamming of the device.

    Therefore, advice on how to remove the carriage from the bike is quite relevant.

    How to remove the bottom bracket from a bike without a puller?

    Despite the fact that a bicycle is a simple structure from a technical point of view, it still needs to be checked and technical equipment and all kinds of maintenance must be carried out. With the help of these procedures, you can greatly extend the life of your device. In addition, if you follow all the norms and more often look closely at the condition of the bike, then you can warn it against significant types of repair, which are also quite expensive.

    It is worth noting the fact that there is absolutely a need for minor repairs or inspection of the bike to contact service centers. In this article we will tell you how to remove the carriage from the bike, due to which you can save on service centers. Consider all the Immediate nuances of this process and other things that you definitely need.

    The characteristic qualities of this type of repair

    Every bicycle owner should know how to remove the carriage from a bicycle. It is worth noting that if the manufacturers of your bike have installed such a closed-type mechanism in it, then there is no point in repairing it. Such devices are usually disposable and the best way out of this situation. Replacing the old unit with a new one.

    In the same case, if your mechanism is open type, then everything is slightly different. It can be easily removed, repaired and installed in its place. Bicycle repair experts say that the bottom bracket. Quite a simple mechanism that can be easily repaired.

    When carrying out repairs, a number of steps must be taken:

    • It is necessary to lubricate all the parts that are present in the mechanism.
    • Backlash must be eliminated.
    • If there are any sounds when driving, then they should be eliminated.

    Convenient instructions for removing this carriage

    A lot of people are wondering how to remove the bottom bracket from a bicycle without a puller. The question is quite interesting, but first let’s look at the instructions for the standard process. It is important to remember that the design of this product contains small bearings, which often crumble. Therefore, you need to understand that it is necessary to carry out the removal and repair with accuracy and care.

    Puller Features

    Before you know how to remove the carriage from a mountain bike, you need to learn about the puller tool. It must be selected taking into account the appearance and structure of the carriage itself. Often the carriage manufacturer must match the puller manufacturer. Today, there are universal types of puller in the world, but, unfortunately, they may not fit this or that mechanism. This mechanism is excellent for removing so-called carriage cups. This is precisely the main feature of the mechanism. Therefore, when using such a device, you should be extremely careful and attentive.

    And how to remove the carriage from a bicycle without a puller?

    Carriage difference

    How to remove the carriage on a speed bike. This is a separate topic. This is justified by the fact that on such a vehicle, this device has a slightly different form.

    On the second bike, where the bottom bracket is of the standard type, it should be externally checked. If it is disassembled, then that is good. But before starting this procedure, pay attention to the condition of its bearings. In order to clean the carriage itself and especially its threads, it is necessary to use gasoline. It is important to remember that such devices need regular cleaning, this is necessary for your safe driving.

    Putting the material in its place

    After cleaning the material, the work does NOT end. The carriage must be attached and reinstalled. This process also brings with it a number of complications, which consist in placing the cups in place. After installation, the device must be lubricated. That’s it, now you know how to remove the carriage from the bike.

    How to remove pedals from a bike without a puller?

    Bicycles are the most popular and convenient form of transport. For some, this is recreation, sports and a great way to attract attention, for example, while performing original tricks on a two-wheeled bike. However, you should forget about timely maintenance and repair. That is why many cycling enthusiasts are faced with the problem of how to remove the pedal from the bike. Having penetrated into the structure of transport, you can easily learn how to carry out repairs yourself. Thus, it will be possible to avoid various unforeseen breakdowns.

    READ  Honda Dio Scooter Won't Start

    Removing the pedal from the bike: Step by step instructions

    So, let’s look at the main steps on how to remove a pedal from a bicycle without a puller:

    • Use a screwdriver to remove the plug from the end of the part.
    • Unscrew the platform from the connecting rod using an adjustable wrench. Right pedal counterclockwise, left pedal clockwise.
    • We unscrew the control nut. At the same time, we hold the connecting rod here using the second key.
    • Remove the washer located at the end of the pedal.
    • Remove the platform from the axle and at the same time hold the bearings. Dismantling ready.

    With clipless pedals, the circuit is a little more complicated. Therefore, before removing the pedal from the bike, you must have a special device. The connecting rod has a thread into which the puller is screwed in and begins to squeeze the connecting rod from the axis. At the end of the work, we put the pedal in place, check the strength of the part, and Install the plug.

    Pedal Features

    Constant mechanical stress on the pedal can cause rotational problems. To quickly cope with them, it is necessary to Heat the connecting rod and behold. As a result, the process of metal deformation will occur. This will help to easily remove here.

    To extend the life of the pedal, use a chain treatment agent. Thanks to the solvent, stubborn dirt such as bolts can be cleaned. We use a solvent and a rag (napkin). The solvent in this case can be replaced with kerosene. Also, DO NOT forget about the toxicity of THESE funds.

    Pedal design

    All pedals, despite their different features, have a common design:

    • Platform. the surface on which the foot rests, which is fixed on the axis.
    • Metal here. a pin made of metal. Has a thread and is screwed into the connecting rod.
    • Bearings. provide torque. Serves as a connecting element between the axle and the platform. There are simple bulk and cartridge bearings, which differ in weight and quality.
    • Bolts, nuts.

    It should be noted that the design of the pedal is not as simple as it seems at first glance. Therefore, before tackling such problems, for example, how to remove the bicycle pedals here, you should carefully study the general design.

    How to remove the pedal from the bike and replace the connecting rod

    The pedal is an uncomplicated part, but the long life can cause some disassembly problems. Therefore, many experts recommend systematic maintenance of the vehicle, despite the fact that many do not attach importance to this issue.

    Let us analyze in which cases it is necessary to remove the pedals:

    • The part is damaged and requires replacement;
    • Lubricate the elements;
    • Replacement or repair of the connecting rod;
    • It is necessary to understand the features of the system and concepts, how it works.

    Before removing the pedal from the bike, the following tools should be prepared:

    • Open-end wrench 15,
    • Adjustable wrench;
    • If there is a non-standard solution of the manufacturer in the fastening elements, then usually the set contains a key for removing the pedal.

    Pedal types

    There are the following types of pedals:

    • Regular (platform)
    • Contact;
    • Combined.
    How To Remove Pedals From A Stealth Bike

    Each of the types of pedals has its own specifics: the first is created for any footwear, the contact type exists for grip with sports shoes and the universal third type, which has a platform on one side and a clutch mechanism on the other. The disassembly method also depends on the type of part. The mechanism of conventional pedals is simpler and faster to disassemble.

    A bike “Stealth

    The manufacturer attracts with serious equipment and carbon frames (StelsNavigator 890DCarbon). An amazing aspect is the attractive price-performance ratio.

    How to remove pedals from a Stealth bike

    It is necessary to remove pedals from a high-speed Stealth bike in the following situations:

    • During scheduled maintenance;
    • If there is a crunch or other squeaks;
    • Replacement with new pedals.

    To do this, you need an 8 socket wrench, grease and a napkin. So, after removing the pedal, you need to take a rag and wipe the threads in the connecting rods. Now you can disassemble the pedal. While holding it, loosen the nut at the other end with a collapsible wrench. Removing this and carefully remove the bearings. Soak all parts in gasoline for a while and wipe with a napkin.

    After completing the preparatory stage, you can proceed to the work itself. Please note that there is a significant difference between how to remove pedals from a bicycle with and without a puller.

    So, first grease the bearings liberally by placing them with balls on the inside of the pedal. Then put on here, screw on the cone and the control nut. Before finishing work, adjust light rotation, no backlash. When you get the desired result, you can screw the pedals to the cranks, Do not forget about the lubricant. On this, the work can be considered completed.

    Therefore, before removing the pedal from the bike, it is advisable to study its construction, paying particular attention to the main elements. It is highly recommended that you read and understand the accessories of all parts and Read the Safety Information. Indeed, driving safety and human health depend on competent assembly and technology. It is important to take a responsible approach to the question of how to remove the pedals on a high-speed bike, due to the complex design of this vehicle.

    How to remove and replace pedals on a bicycle

    A situation has arisen that it is necessary to unscrew the pedals from the bike, but you do not know how to do it correctly. Let’s see how to perform this operation quickly and easily.

    How to remove the pedal from the bike and replace the connecting rod

    The pedal is an uncomplicated part, but the long life can cause some disassembly problems. Therefore, many experts recommend systematic maintenance of the vehicle, despite the fact that many do not attach importance to this issue.

    Let us analyze in which cases it is necessary to remove the pedals:

    • The part is damaged and requires replacement;
    • Lubricate the elements;
    • Replacement or repair of the connecting rod;
    • It is necessary to understand the features of the system and concepts, how it works.

    Before removing the pedal from the bike, the following tools should be prepared:

    • Open-end wrench 15,
    • Adjustable wrench;
    • If there is a non-standard solution of the manufacturer in the fastening elements, then usually the set contains a key for removing the pedal.

    Pedal Features

    Constant mechanical stress on the pedal can cause rotational problems. To quickly cope with them, it is necessary to Heat the connecting rod and behold. As a result, the process of metal deformation will occur. This will help to easily remove here.

    To extend the life of the pedal, use a chain treatment agent. Thanks to the solvent, stubborn dirt such as bolts can be cleaned. We use a solvent and a rag (napkin). The solvent in this case can be replaced with kerosene. Also, DO NOT forget about the toxicity of THESE funds.

    Pedal types

    There are the following types of pedals:

    • Regular (platform)
    • Contact;
    • Combined.

    Each of the types of pedals has its own specifics: the first is created for any footwear, the contact type exists for grip with sports shoes and the universal third type, which has a platform on one side and a clutch mechanism on the other. The disassembly method also depends on the type of part. The mechanism of conventional pedals is simpler and faster to disassemble.

    Pedal design

    All pedals, despite their different features, have a common design:

    • Platform. the surface on which the foot rests, which is fixed on the axis.
    • Metal here. a pin made of metal. Has a thread and is screwed into the connecting rod.
    • Bearings. provide torque. Serves as a connecting element between the axle and the platform. There are simple bulk and cartridge bearings, which differ in weight and quality.
    • Bolts, nuts.

    It should be noted that the design of the pedal is not as simple as it seems at first glance. Therefore, before tackling such problems, for example, how to remove the bicycle pedals here, you should carefully study the general design.

    How to remove pedals from a Stealth bike

    It is necessary to remove pedals from a high-speed Stealth bike in the following situations:

    • During scheduled maintenance;
    • If there is a crunch or other squeaks;
    • Replacement with new pedals.

    To do this, you need an 8 socket wrench, grease and a napkin. So, after removing the pedal, you need to take a rag and wipe the threads in the connecting rods. Now you can disassemble the pedal. While holding it, loosen the nut at the other end with a collapsible wrench. Removing this and carefully remove the bearings. Soak all parts in gasoline for a while and wipe with a napkin.

    READ  Child 130cm Which Bike

    After completing the preparatory stage, you can proceed to the work itself. Please note that there is a significant difference between how to remove pedals from a bicycle with and without a puller.

    So, first grease the bearings liberally by placing them with balls on the inside of the pedal. Then put on here, screw on the cone and the control nut. Before finishing work, adjust light rotation, no backlash. When you get the desired result, you can screw the pedals to the cranks, Do not forget about the lubricant. On this, the work can be considered completed.

    Therefore, before removing the pedal from the bike, it is advisable to study its construction, paying particular attention to the main elements. It is highly recommended that you read and understand the accessories of all parts and Read the Safety Information. Indeed, driving safety and human health depend on competent assembly and technology. It is important to take a responsible approach to the question of how to remove the pedals on a high-speed bike, due to the complex design of this vehicle.

    How to remove the pedals

    • This is best done with the bike on wheels. Why? The fact is that sometimes it takes a lot of effort to unscrew it and you have to use the weight of the whole body. It is easier to do this while the bike is on its wheels than when it is hanging on a rack.
    • Remove the right pedal. To do this, it is best to put the right crank at the 3 o’clock position: the crank is horizontal to the ground and turned towards the front wheel. Taking into account that the right pedal has a normal thread, we unscrew it like a normal thread. counterclockwise.
    • Then remove the left pedal. We put the left crank in the 9 o’clock position. It is again horizontal to the ground and turned towards the front wheel. Remember that there is a left-hand thread on the left pedal and unscrew it clockwise.

    How to remove pedals from a stealth bike. Pedal design features

    Such a simple element as a bicycle pedal has its own nuances. Today there are three types of parts:

    • Platform;
    • Contact pedals on a bicycle;
    • Combined.

    Each of them has its own specifics: the first are designed to grip with any shoe, the second. for special cycling shoes, and the third are universal and have a contact mechanism on one side and a platform on the other. Thus, the bicycle pedal provides a comfortable ride.

    The design also includes a connecting rod, which does not require special maintenance and does not require maintenance. In case of mechanical damage or problems, you just need to change the connecting rod to a new one. All the nuts that secure this part are very easy to unscrew. First you need to remove the pedals, disassemble the cone and, if necessary, lubricate the bearings. Repair is not difficult and does NOT take a long time. In order to remove the connecting rod, you need a special puller or certain skills. It is quite efficient and fast, otherwise it will take a lot of time and effort to disassemble the structure. The connecting rod is held by a large bolt on the shaft, while driving, the place where they touch becomes dirty and it is very difficult to remove the connecting rod.

    In order to avoid problems with the pedals of the technique, it is necessary to regularly inspect and troubleshoot. Bearings are also important. There are several types of them, but simple bulk and cartridge ones are especially popular, which differ in weight and quality. Professionals prefer functional and reliable parts. Is there a large assortment in the modern market of sports equipment and parts? And choosing and replacing suitable pedals for your bike is not difficult. Repair of this element is quite simple.

    How to remove pedals from a bike

    The pedals should be removed when:

    • The bike must be packed in a cover;
    • The pedal creaks, crunches and therefore needs to be cleaned;
    • Pedals Do not creak yet, but you do regular maintenance (if everything is in order, then the pedals are cleaned enough, Lubricate and adjust once a year or two)
    • You change the pedal to a new one;
    • There is a need to set up a new pedal.

    To do this, you need a special pedal wrench (it can be replaced by a 15 mm open-end wrench or a 6 or 8 mm socket wrench), rags and grease.

    How to remove pedals from a bike

    Put the bike on wheels (using a special stand, which keeps the bike suspended, is not the best option for this particular case, because when unscrewing the pedals, you have to Apply a very large force, which can be extinguished by the stand structure).

    Please note that the threads in the left and right pedals are different! This is to ensure that the left pedal does not spontaneously twist when you cycle. Thus, you unscrew the right pedal (on the side where the stars are) as usual, counterclockwise; but to loosen the left pedal, you need to turn the key clockwise. This is very important to remember so as not to tighten the left pedal even more.!

    If you need to remove both pedals, start with the right. Set the connecting rod parallel to the ground, pointing it forward. So it will be more convenient for you to unscrew the nut, pressing your weight on the key; you are also less likely to hit the frame stays in the rear wheel area. Be careful not to injure your fingers in the chainrings! After loosen the pedal, unscrew it completely, while making sure that the washers do NOT roll away anywhere, which may be there.

    To unscrew the left pedal, orient the crank in the same way. We remind you again: here you need to unscrew clockwise!

    After you have removed the pedal, first of all, so as not to forget, wipe the threads in the connecting rods. remove any remaining grease and dirt.

    How to disassemble, adjust and assemble the pedal

    Now proceed to disassemble the pedal itself. Holding it from the end that was screwed into the connecting rod, Loosen the nut at its other end with a hexagon or a second wrench. If you DO NOT see a nut or a groove for a hexagon on the second side of the axis, look, perhaps, there is an overlay. pry it with a knife and with it. Having unscrewed all the nuts, Remove all the bearings.

    Wash all parts in gasoline or kerosene, wipe dry. After that, you can start assembling.

    Apply grease to the bearings and lay them so that the balls are oriented towards the inside of the pedal. Now. Put it on, screw the cone and the lock nut (if there were washers, then we also place them where they were).

    Before you screw the pedal to the bike, you need to adjust it. Take it here and spin it. The pedal should rotate very easily, and there should not be any backlash. well, perhaps only the most minimal. The adjustment is carried out as follows: by unscrewing or tightening the lock nut, ensure that the pedal rotates with sufficient ease. Once you get a satisfying effect, you can screw the pedals to the cranks (Apply some lubricant to the threads).

    At the same time, remember that you need to tighten them to the side, the opposite of unscrewing: the right, as usual, clockwise, and the left counterclockwise. Start spinning the pedals with your hands first, so that you can plant them as accurately as possible, and not tearing off the thread.

    If you have NEVER removed wheels from a bicycle before, then you may also be afraid that you will NOT cope, especially with the rear wheel (after all, there is a chain, a bunch of stars and this tricky switch!). But now we will tell you everything about this simple operation.

    In this article we will answer Not only the question “why does the bike creak”, but also tell about all the extraneous sounds that may appear during riding: creak, grinding, crunching, rustling, whistling, crackling, banging.

    So, we continue the series of articles on disassembling SEPARATE bicycle assemblies. We have already unscrewed the pedals, today we will tell you how to remove the connecting rods.

    Sometimes it becomes necessary to disassemble the bike. As a rule, this is done for its transportation, storage, or in order to replace some of its nodes.

    Summer is just around the corner, if you have not yet had time to prepare the bike for the new season, now is the time!