How to make front brakes on a bike

Adjusting the position of the pads

Apply the brake by squeezing the levers and placing the cable guide (C) against the stop (D). Loosen the block fixing bolt (K) with a hexagon. We press the lever with the block to the rim and set the block so that it:

  • adhered to the rim with the entire surface
  • did not touch the tire
  • located parallel to the rim

make, front, brakes, bike

In this position, the block must be fixed by tightening the bolt. When tightening the bolt, the block may move and must be corrected. It will be easier if you find an assistant who will grip and hold the brake lever while you tighten the bolt.

If your brakes squeal, try the following.

Before tightening the bolt, place a folded sheet of paper under the rear (in the direction of travel) of the shoe, then tighten the bolt. So the pads will be smoother to press against the rim during braking (first at the front, then at the rear) and will not squeak.

We do similar operations with the second block.

How to set up rim brakes

Vibrators do not lose popularity. Ease of maintenance, cheap consumables and unpretentious operation. an excellent option for those who use the bike primarily for moving, without extreme and overloading.

The principle of operation is simple. when pressed, the brake lever pulls the cable (G), which moves the brake levers (I), pressing the pads (J) attached to them against the wheel rim. When the handle is released, the levers return to their original position, installed on them by springs. In this article, we will analyze how to set up and adjust rim brakes:

Varieties of rim brakes

Rim brakes are divided into several types:

  • tick-borne;
  • cantilevers;
  • V-brake (vector mechanical);
  • hydraulically driven.

Caliper brakes. previously popular modifications, are now rare on the market. They are a classic model of rim brakes with attachment to the fork or stays of the bicycle frame. Design features and operating principle:

  • Consist of a handle, a drive cable, two movable bows and brake pads.
  • The handle is attached to the handlebars of the bicycle, a cable is pulled from it and fixed on the clamping side of the arches. The body itself is attached strictly above the wheel, pads are screwed to the lower mounts of the arcs.
  • Through the cable, the force is directly transmitted to the clamping part of the arcs, due to which they are compressed, and the pads are in contact with the rim.
  • Responsible for unclamping is an elastic metal insert or spring built between the levers.

The levers have a single axis of rotation and move towards each other like pliers pincers. Hence the name. tick-borne. Advantages. ease of installation, simple setup. Cons. weak braking force, low modulation, high abrasion of the pads, require frequent debugging. Fits on road racing bikes and optionally as a front rim brake on road models.

Cantilevers belong to the second type of disappearing brakes. The principle of their work is to extend the levers under the action of a taut leash. The principle of operation of the cantilever brake:

  • Through the main cable, the force is transmitted to the jumper.
  • The cable pulls the jumper up, the leash attached to it is pulled.
  • The leash connects both levers, which are rigidly attached to the frame.
  • Due to the convergence of the levers, the pads approach the rim.

The cantilevers are dirt resistant, will not bump the tire and are easy to install. Significant disadvantages include:

  • decrease in braking force as the leash is pulled;
  • you need to create a high effort to stop the bike completely;
  • difficulty of adjustment.

In justification of the latter, it should be noted that the position of the pads can be adjusted within wide limits.

READ  What the Bike Roll Depends on

V-brake is a common type of rim brake on high-speed bicycles. Compared to cantilevers, it has a higher precision and longer shoe longevity. They are also easy to remove and repair yourself.

The vectors are partially similar in design to cantilevers: the front brake levers are bolted to the fork, the rear brake levers are attached to the upper stays. The legs are connected to each other by a pulling cable. The drive cable is brought to one side, but due to the straight shape of the tie, the forces are equally transmitted to both levers.

Hydraulic bicycle rim brakes are a more advanced mechanical model. The drive system consists of a control cylinder, a hydraulic line and power cylinders. The forces from the handle are transmitted to the master cylinder, which, through the oil, acts on the power cylinders. Those, in turn, move the pads towards each other.

Advantages. high compression force and efficiency, excellent modulation. Disadvantages. deterioration of work with a blockage of the hydraulic line, complex repairs. Used a similar type of brakes for freeride and trial.

Rim-type brakes have low brake pad travel, which means they wear less during operation. A significant disadvantage of this approach is the inability to be used on wheels, even with minor rim curvatures. Sensitive brakes will rub against the wheel on the fly, causing reduced speed and increased pad wear.

How to install and adjust the V-brake yourself

  • Attach the levers to the bike frame.
  • Insert the drive cable into the brake lever.
  • Install the handle on the steering wheel, insert the cable into the grooves on the frame (if any).
  • Connect the cable to the levers and put the spring.

After installation, you will definitely need to adjust the brakes.

The accuracy of the mechanism depends largely on its settings. So, even an expensive system will not work well without proper adjustment, and conversely, a mid-range V-brake can outperform a disc brake in terms of efficiency. What needs to be done to adjust the brakes?

Adjust the cable tension. After adjusting, the brake should instantly respond to the squeeze of the handle and rebound when it is released. If the pads do not move away from the rims, this indicates insufficient tension. On a tight cable, the handle will be hard to press, and the sheath may burst.

The tension is adjusted with a bolt on the side of the levers. The setup looks like this:

  • Reset Springs.
  • Loosen the cable fixing bolt.
  • Adjust the tension so that in the fully clamped position, the distance from the handle to the handlebar corresponds to the thickness of the finger.

If damage is noticed on the cable sheath, it is recommended to immediately install a new set.

Clearance adjustment. The optimal distance is 2. 3 mm from the edge of the pad to the rim. Determination of brake pad wear: cannot be used when the diverter grooves are completely erased (the whole surface is flat).

How do I fit new pads? The location relative to the rim affects the size of the contact area of ​​the pads with it, the braking force and the life of the material. For brake pads with soft rubber surfaces, install them with the leading edge closer to the rim. Brake pads made of rigid material are placed strictly parallel to the surface of rotation of the wheel.

If your bike has cartridge pads, you only need to change the pads. Their position is set with a cotter pin; before removing the old surface, it is removed from the body. Similarly, in the reverse order, insert a new pad and fix it with a cotter pin.

Adjustment of the position and displacement of the shoe housings are carried out by means of a bolt and washers. For accurate fixation, you need to squeeze the brake and set the position of the pads strictly on the surface of the rim.

The last step will be to test the operation of the system in practice, that is, in real driving conditions. As a rule, the V-brake setting is obtained immediately. However, if braking is delayed or the handle does not fully return to its original position, the brakes must be readjusted.

How to adjust the brakes on your bike yourself?

The question of how to adjust the brakes on a bicycle is very rarely posed to the owners of modern bicycle bikes, since the quality of modern braking systems is so high that the settings installed at the factory during the production process do not go astray for years. However, in any case, the cyclist needs to know the intricacies of their settings and carry out preventive maintenance at least once a season. This will allow you to extend the life of your bike and protect you from possible accidents that may happen to you on the road.

READ  Is it possible to ride a bike with scoliosis

We set the levers symmetrically

In order for the left and right pads to wear evenly, they must be at the same distance from the rim. Adjustable by spring tension on the brake levers. To equalize the force that returns the left and right brake levers to their original position, use the adjusting bolts located at the base of the levers.

By twisting the bolt clockwise, we tighten the spring, unscrewing it. we loosen it. By pressing and releasing the brake, we check the uniformity of the removal of the pads from the rim. Tighten the bolts on the left and right sides until the pads move the same distance when the brake lever is released.

How to set up rim brakes on a bike

The braking system is one of the most important technical components of a bicycle. The safety of both the cyclist and other road users directly depends on its condition. Good brakes are essential in any situation, from riding in parks to tough cycling.

How to Install Brake Cables & Housing | Bicycle Repair

In the modern classical sense, a bicycle brake is a pressure mechanism that acts on the wheel rim. In fact, there are several types of brakes, however v-brake (rim) is the most common option on bicycles of various classes.

Adjusting the brakes on a bicycle

Adjusting the brakes on a bicycle should be carried out regularly. such maintenance will guarantee the safe operation of the vehicle. There are two main types of brakes on modern bicycles. rim and disc brakes, but disc brakes can be mechanical or hydraulic. The type of brake system installed on a particular bike will determine the process of their maintenance.

How to set up rim brakes

Vibrators do not lose popularity. Ease of maintenance, cheap consumables and unpretentious operation. an excellent option for those who use the bike primarily for moving, without extreme and overloading.

The principle of operation is simple. when pressed, the brake lever pulls the cable (G), which moves the brake levers (I), pressing the pads (J) attached to them against the wheel rim. When the handle is released, the levers return to their original position, installed on them by springs. In this article, we will analyze how to set up and adjust rim brakes:

Checking the condition of the brakes

First of all, unfasten the brake, as shown in the photo.

Check how the cable (G) moves in the shirt (A) by pressing and releasing the brake lever and pulling the cable back with your finger. the movement should be free, without delay. If the cable pulls hard, it may be damaged, the shirt or cable guide (C), or dirt has accumulated inside the jacket or cable guide. They must be removed and cleaned or replaced.

Check the condition of the pads (J). Grooves for the drain of dirt should be visible on them (the block should not be smooth). Worn pads without grooves must be replaced. Check that the pads are complete with washers and that they are correctly installed.

Brake Caliper Mounting & Adjustment. Dual Pivot

Observe the order of the washers when installing new pads.

The brake levers (I) must swing freely in their seats and spring apart after being compressed. If the movement is difficult, the brake during operation may get stuck in the closed position and rub the pad on the rim. In this case, you can remove the levers from the seats, clean and lubricate the contact points and reinstall.

When installing, make sure that the protruding pin on the arm fits into the hole in the frame, and that the hole on the left and right arm is the same.

Braking system characteristics

The following terms are used to qualitatively describe the operation of rim brakes:

  • impact force;
  • efficiency;
  • wear resistance;
  • modulation;
  • service requirements;
  • comparative features.
READ  How to disassemble a bicycle wheel with 6 sprockets

The force of impact, or braking, is a parameter that shows how much the brake can clamp the rim so that the bike cannot be moved. Maximum effort is required only to completely stop and lock in place. On the road, the effort is not fully used to adjust the speed. The range of action on the wheel rim by pressing the knob is called modulation, or accuracy, of the brakes.

An active cyclist uses his transport not only in dry and cloudless weather. Rain, mud, sand. everyone who rolls out their bike on long trips will have to face this. The effectiveness of brakes allows you to describe their behavior in a wide variety of conditions.

Durability is a measure of durability, taking into account the prescriptions for the use of the bicycle as a whole. Timely maintenance can increase the service life of the braking system. Service Requirements provide guidance on how to properly install and adjust the machine, how often to do this, and guidance on how to replace parts.

Setting up disc brakes

As a rule, adjustment of disc brakes consists in periodically tightening the cable. But often you have to replace the pads, however, on disc brakes they wear out longer than on rim brakes. First you need to find out which specific disc brakes are installed on the bike. brake pad adjustments for hydraulic and mechanical systems will differ.

Experts recommend taking note of the following points:

  • If there are hydraulic disc brakes on the bike, then replacing the pads may not be necessary. they are able to do it on their own. But one nuance should be taken into account. if the hydraulic system is closed, then you will have to adjust the pads manually. for this, special valves are provided.
  • If you have to adjust disc mechanical brakes, you will need to pull the cable according to the above instructions and check the location of the pads. the distance between them and the disc should be within 0.2-0.4 mm.
  • In order to adjust the pads with disc mechanical brakes, you need to use special bolts. by tightening them, you can see how the pad moves. You need to be especially careful when setting the distance between the pad and the disc. 0.3 mm is too small, it is easy to make a mistake.

After carrying out the work, be sure to check the operation of the brake system in action. ride your bike for a few meters and try to brake. If the cable is too tight, or the pads are too close to the disc, then too sharp braking will occur. this is a surprise in which the cyclist begins to move forward, but without his vehicle. Therefore, when driving for a test, you need to be extremely careful and careful, if necessary, the disc brake system is adjusted again taking into account previous errors.

Adjusting the position of the pads

Apply the brake by squeezing the levers and placing the cable guide (C) against the stop (D). Loosen the block fixing bolt (K) with a hexagon. We press the lever with the block to the rim and set the block so that it:

  • adhered to the rim with the entire surface
  • did not touch the tire
  • located parallel to the rim

In this position, the block must be fixed by tightening the bolt. When tightening the bolt, the block may move and must be corrected. It will be easier if you find an assistant who will grip and hold the brake lever while you tighten the bolt.

If your brakes squeal, try the following.

Before tightening the bolt, place a folded sheet of paper under the rear (in the direction of travel) of the shoe, then tighten the bolt. So the pads will be smoother to press against the rim during braking (first at the front, then at the rear) and will not squeak.

We do similar operations with the second block.