How to change pedals on a stealth bike

How to check the pedal

It is advisable to check the condition of the pedals, their tightness, the absence of backlash and the condition of the case before each trip. You can just stand with your foot on it, and then, twisting, watch and listen to how it rotates on the axis. If there is no visual beating and unnecessary sounds. everything is fine, you can go.

Remember, if the pedal twists out, breaks or is lost while driving, you are unlikely to be able to go somewhere, and the risk of injury is quite high.

You can read more about pedals in the article

  • Types of bicycle pedals. Which one to choose for your bike.
  • What are toe clips and what are they for. What are they and how to choose them correctly.
  • Bike Pedal and Crank Thread Compatibility

How to change Peloton Bike Pedals / How to Remove bike pedals and install clip in pedals

When you may need to remove bike pedals

  • For maintenance. For example, a crunch or creak appeared and you need to clean and lubricate them.
  • When replacing old pedals with new ones, or replacing connecting rods.
  • When packing the bike into a cover or to reduce the space occupied when transporting it.
  • When preparing your bike for long-term winter storage. Again to minimize bike space
  • As an anti-theft agent. The method is very effective. well, where will you go on such a bike. The trick here is that they should be removed easily and simply. The tool for this and a small bag in which the removed pedals will be folded should always be with you in your bike bag. You will not wear them all the time in your hands.

How To Change Pedals– Remove and Replace Your Pedals

The peculiarity of the pedals is that they have symmetrical threads.

change, pedals, bike

Each of them must have a label: which is left and which is right. Usually these are the English letters L. Left (left) and R –Right (right), respectively, for the left and right pedals.

The left pedal is always made with a left hand thread. This means that it twists counterclockwise and unscrews clockwise.

On the right. conventional right hand thread. Twists clockwise and unscrews counterclockwise.

This is done so that when the pedals are spinning while the bike is moving, they do not unscrew.

It’s easier to remember the rule: the pedals are unscrewed against the direction of the bicycle. twist to the rear wheel, and twist in the direction of travel. turn to the front wheel.

How to put a pedal on a bike.

I would like to immediately highlight one question that sometimes arises from some cyclists. It is connected with the compatibility of the thread on the pedals and connecting rods and the different standards adopted in modern bicycle construction and in Soviet times. The fact is that the threads on modern pedals do not fit the threads cut in the Soviet connecting rods. This issue is discussed in more detail in the article “Thread compatibility on bicycle pedals and cranks”.

If you are all right with this question, consider how to put the pedal in the connecting rod.

    Check the threads for grease before installing the pedal. If not, it is better to apply a layer of lubricant to the threads. So you will protect it from corrosion, from “sticking” to the connecting rod and make your life easier in the future. it will be easier to remove later. You can use lithol, grease and other waterproof lubricants.
READ  How to make a bike step with your own hands

By the way, before starting the installation process, it would be very good to clean from old grease and dirt with a degreaser not only the thread on the pedal axis, but also the thread in the connecting rods.

Degreaser. it is a special degreasing compound designed to remove dirt, grease, oil.

  • It is best to begin to twist the pedal with your hands, strictly perpendicular to the connecting rod axis. So the least likely to damage the thread when the axis is misaligned.
  • All actions during setting are similar to removal, only they need to be twisted in the other direction, compared to unscrewing.
  • If there is a slot for a hexagon wrench at the end of the pedal axis, then it can be screwed in with a hexagon. The minus of the hexagon is that it will not work to give a strong load and screw the pedal well. Therefore, it is best to tighten it first with a hexagon, and then finally tighten it well with an open-end wrench.
  • It is necessary to twist the axle into the connecting rod strongly, but without fanaticism. It is very difficult to break the thread there, but it will be difficult to untwist the fanatically tightened thread.
  • After installation, remove any excess grease that has formed around the connecting rod connection. So dirt and dust will not accumulate in this place.
  • What tool are pedals removed

    • Open-end wrench 15 mm
    • Various universal bicycle wrenches that have a 15mm wrench.
    • Adjustable wrench.
    • Some models are removable and reattached with 6/8/10 mm hex keys
    • There are special pedal wrenches that combine 15 open-end wrenches and hex wrenches in one tool.

    When using an adjustable wrench, be sure to pay attention to its thickness. The fact is that the distance between the pedal mount and the connecting rod is not large, and not every adjustable wrench will fit there. Some types of wrenches come with thin jaws that can be used. Open-end wrenches or special pedal keys are great for this operation.

    Classic bicycle pedals

    This type of elements is one of the most common options, the configuration of which has been known since the times of the Soviet Union. On modern modifications, improved versions are used. These models are reliable when made with quality components. Design:

    • housings with an internal axis;
    • bearings;
    • a pair of overlays;
    • bolt fastening;
    • the presence of reflectors in the form of reflector strips is possible;
    • sometimes the body part is made not of a metal alloy, but of plastic.

    These pedals can be used on almost all types of bicycles. The use of such modifications is not practiced only on stunt and other specific bikes designed for extreme sports. This is due to the fact that when performing jumps, the pedals on a high-speed bike undergo critical loads that they can not withstand. The advantages include light weight, ease of maintenance and low cost.

    Assembly

    After disassembling and replacing the lubricant, as well as faulty elements, they begin to assemble the part. It is performed in the following sequence:

    • A reasonable amount of grease is applied to the seat of the second bearing. A characteristic indicator is the ability of the balls to stick to it without falling out of the bowl.
    • Place the insides of the second bearing in the bowl. For convenience, tweezers can be used. The balls are pre-counted. It is important not to confuse them with the elements of the first bearing.
    • Position the axle carefully so as not to displace the balls. After placing the part in its place, make sure that it does not fall out back.
    • Apply grease to the seat of the first bearing, put balls on the bowl.
    • A cone is screwed onto the axle, followed by adjustment of the tightening. In the process of tightening the part, check the absence of lateral and longitudinal backlash. They should not be present, but the pedal should rotate easily.
    • Put on a washer, tighten the lock nut, install a protective plug.

    This completes the assembly. The right element in the connecting rod is twisted clockwise, the left one. counterclockwise.

    READ  How to set the speed switch on a bike

    Contact pedals

    These products are used as parts for mountain and road bikes. Some craftsmen also mount them on hybrid versions. The system differs from the above-mentioned analogs by the presence of a special mechanism responsible for the reliable fixation of characteristic shoes. The design makes it possible not only to move the pedal along the trajectory, but also to pull it up, which significantly increases the efficiency of driving, reducing the expenditure of physical forces.

    The complicated configuration, in turn, leads to an increase in the price of the product, as well as additional costs for the purchase of special shoes. Next, consider methods for replacing, disassembling and lubricating the elements in question.

    Platform versions

    The configuration of this type of bicycle pedal, which is used on modern models, is a single wide platform. The part is made of reinforced plastic, aluminum or a combined material. The housing is a one-piece part, in the inner part of which there are bearings, a threaded axle and a washer with a locknut. Additional reflectors may be available.

    The advantages of elements of this variety include increased strength, which makes it possible to operate them on mountain, road and urban models. It is not recommended to mount these elements on road modifications due to their large mass. Among other disadvantages are the high price and massiveness.

    Disassembly

    How to disassemble the bicycle pedal after removing it? This operation consists of several stages:

    • Remove the plug on the end of the element. To do this, pry it off with a sharp object, such as a screwdriver.
    • Unscrew the control nut with a spanner wrench, remove the intermediate washer.
    • Carefully unscrew the cone of the bearing block, making sure that the balls do not fall apart. After shooting the part from the axis, it is advisable not to turn the pedal, holding it, in order to avoid the axle falling out of the body.
    • The ball bearings are removed and set aside. Better to count them so that there are no misunderstandings during assembly.
    • Take out the hull axle. The operation is carried out over a table or other surface, since the balls of the second bearing may spill out.
    • Then the elements are taken out and counted. They should coincide in quantity with the first analogue. Do not mix and interchange parts, because during operation they have got used to each other.
    • Cleans attachments of old grease, including cones, seats, axle and everything else. The process is carried out with the help of a clean rag or “wedge”.
    • All elements are inspected for cracks and other damage. In the case of over-tightening the retainers and insufficient oil, the bearing housing can be extremely worn out.

    How to unscrew the pedals on a bike?

    It is very simple to dismantle these elements for repair or replacement. It must be borne in mind that the right and left parts are unscrewed in different directions (the first is clockwise, the second is counterclockwise).

    The pedals can be removed using an adjustable wrench or other suitable wrench. Since the gap between the connecting rods is 12 millimeters or less, the length and thickness of the tool edges must be considered.

    Removing the pedals from the bike is easy enough, but don’t forget about preparing tools and materials, as well as possible problems. The main thing is to keep the entire system in order, since in case of damage or other problems, the inconvenience of using the bike will be very great.

    How to remove pedals from a bicycle, disassemble and replace with new ones?

    The pedal is a simple part, but due to some mounting features and a very long service life, not every cyclist is able to remove them from their bike on their own. Why remove the pedals?

    • Change them after damage.
    • Pedal lubrication.
    • Connecting rod repair or replacement.

    First, let’s look at how they are arranged, what types are there, what features should be considered, what tools to prepare before work.

    Required tools and materials

    Before removing the pedals, it is necessary to prepare the tool and auxiliary materials that are most likely to be needed.

    • lubrication. it is recommended to clean and lubricate the removed parts;
    • cleaning rags;
    • kerosene or solvent. in case the axles do not unscrew or there are large contaminated areas.
    • an adjustable wrench is a universal solution, a small one is desirable, otherwise it will be difficult to get to the nut;
    • open-end wrench for 15. fits almost all models;
    • bicycle kit. in case of emergency;
    • pedal wrench. supplied by manufacturers for non-standard nuts and just in sets;
    • puller. an addition to the foot pedals. a standard tool, often supplied by the manufacturer, serves to hold the axle when turning to the side with a wrench.
    READ  Do-it-yourself waterproofing of the kugoo m4 pro electric scooter

    Change Pedals on a Bicycle: How to Change Pedals on a Bicycle: How to Change Pedals on a Bicycle | REPLACING THE BIKE PEDAL

    Removing the pedals

    After preparation, you can proceed with the removal process. For conventional mechanisms, it looks like this:

    • We move the system to the working side. in the direction of the steering wheel.
    • We try to carefully unscrew the pedals from the connecting rod.
    • Remove the plug at the end of the platform, open the lock nut.
    • Unscrew the lock nut, holding the axle at the connecting rod with the second key.
    • Remove the washer (also at the end).
    • Unscrew the cone.
    • We remove the platform from the axle, holding the bearings (it is better to remove them separately, if they are bulk, then put a rag or sheet so that they do not roll far).
    • Pedal removed and disassembled!

    It is important not to forget that the left and right pedals are unscrewed from the connecting rod in their direction: on the right axis. the right thread, on the left. the left.

    The contact devices are a little more difficult to disassemble, but they will not cause any problems. when twisting and disassembling, a puller is used, which should hold the axis with a small contact pad.

    Stages of work

    In order to remove the pedals, you need a fairly simple tool. a wrench and a hexagon. The latter may not be suitable for some types of equipment and you can use either a crank puller or a wrench. Often only an adjustable wrench is used. Before starting work, you should know that the right pedal axis is unscrewed counterclockwise, and left. in the clockwise direction. Step-by-step instruction:

    How To Install/Remove MTB Pedals EASILY!

    • Using a screwdriver, remove the special plug from the end;
    • Then you need to hold the axis with a key and unscrew the nuts;
    • Next, disassemble the washer, unscrew the cone;
    • Remove the bearings very carefully;
    • It is necessary to remove the pedals from their axis.

    How to remove pedals from a bike

    A bicycle is the most affordable, fairly convenient and useful means of transportation. Many people are fond of riding two-wheeled vehicles, someone performs virtuoso stunts on BMX, but in any case, timely maintenance and repair of equipment plays an important role. This avoids many unforeseen problems. There are times when the question arises: how to remove the pedals from the bike? Going a little deeper into the intricacies of the design, you can effectively carry out vehicle repairs yourself. Thus, you can feel the technique as much as possible, customize it according to individual preferences and easily deal with unexpected breakdowns.

    Required tools and materials

    Before removing the pedals, it is necessary to prepare the tool and auxiliary materials that are most likely to be needed.

    • lubrication. the removed parts are recommended to be cleaned and lubricated;
    • cleaning rags;
    • kerosene or solvent. in case the axles do not unscrew or there are large contaminated areas.
    • an adjustable wrench is a universal solution, a small one is desirable, otherwise it will be difficult to get to the nut;
    • open-end wrench for 15. fits almost all models;
    • bicycle kit. in case of emergency;
    • pedal wrench. supplied by manufacturers for non-standard nuts and just in sets;
    • puller. addition to the foot pedals. a standard tool, often supplied by the manufacturer, serves to hold the axle when turning to the side with a wrench.