How To Assemble A Rear Wheel On A Sports Bike

Camera replacement

First of all, you need to deflate the wheel. Unscrew the cap and press the nipple to deflate the air. If there is no damage chamber and there is no air in it, simply remove the cap. To remove the tires, you need mounting paddles, which will be convenient for prying the camera until it becomes easy to pull it off the rim.

The camera can be replaced without tools. First, the nipple is inserted into the hole in the rim, after which the tire is evenly put on the rim. Finally, the camera needs to be pumped up to the desired state.

When to service the rear hub

For the correct operation of the wheel and its main parts, incl. Bushings, it must be kept in good condition at all times. It needs lubrication, and its body needs to be tightened periodically. In addition, replacing the bearing balls and adjusting the pads on the brake bushings will not interfere.

Rear hub service is essential, as in cases where this does not happen, the entire wheel may need to be repaired. Therefore, it is better to take care of your bike in the long run. It should be noted that servicing the rear hub is not much more difficult than the front hub.

Maintenance is necessary in the following cases:

  • If you hear body noise when the bike is moving or rocking.
  • Backlash.
  • If the bearings crunch.
  • Poor rolling dynamics.

If you do not pay attention to the signs of “illness” described above and use it for a long time if available, it can quickly fail.

READ  How To Attach The Basket To The Front Of The Bike

Repair, in turn, will be much more expensive than simple wheel maintenance, which you can do yourself. Therefore, at the beginning of each season, check the wheel for play, and that the bearings are NOT too tight.

Removing the sleeve

We remove the cassette from the asterisk using a special Stripper, a key and a whip. First, we insert the puller into the grove, then we insert the key into it, put on the whip on the big stars, hold the stars with it, and unscrew the nut. Now that the nut is unscrewed, you can easily remove the cassette from the sprocket.

Before disassembling the sleeve, the tension on the spokes should be loosened so that it can easily be pulled out of the engagement. When parsing this part, it is better to decompose all of its components in order, so that later you can precisely put everything in place. If necessary, you can replace the bearings, which, unlike metal components, are the first to fail. Timely service of the bushing will ensure its long service life, so do not neglect the cleaning and lubrication of the mechanism parts.

In the reverse order, the spokes are tightened exactly as far as they have been loosened, it is important not to overtighten them, but the parts must be firmly fixed. The cassette is put on the sleeve and the whip is tightened.

After all the procedures performed, due to which the wheel and its parts were dismantled, you need to know how to assemble the rear wheel of the bike back.

Removing and installing bicycle wheels

This article will guide you through removing and installing front and rear bicycle wheels.

How To Assemble A Rear Wheel On A Sports Bike

Removing the sleeve

We remove the cassette from the asterisk using a special Stripper, a key and a whip. First, we insert the puller into the grove, then we insert the key into it, put on the whip on the big stars, hold the stars with it, and unscrew the nut. Now that the nut is unscrewed, you can easily remove the cassette from the sprocket.

READ  How To Pull A Wheel On A Bicycle

Before disassembling the sleeve, the tension on the spokes should be loosened so that it can easily be pulled out of the engagement. When parsing this part, it is better to decompose all of its components in order, so that later you can precisely put everything in place. If necessary, you can replace the bearings, which, unlike metal components, are the first to fail. Timely service of the bushing will ensure its long service life, so do not neglect the cleaning and lubrication of the mechanism parts.

In the reverse order, the spokes are tightened exactly as far as they have been loosened, it is important not to overtighten them, but the parts must be firmly fixed. The cassette is put on the sleeve and the whip is tightened.

After all the procedures performed, due to which the wheel and its parts were dismantled, you need to know how to assemble the rear wheel of the bike back.

The main components of the wheel

A standard bicycle wheel consists of several main parts:

  • The bushing is the central part, through which the torque is provided. The interior of the rear hub is slightly more complex than the front. NOT every sleeve can be disassembled at home, some variations without special equipment and knowledge It is better not to touch. And also brakes can be attached to this part;
  • Spokes connecting the hub to the rim;
  • The rim on which the tire is mounted;
  • Tire.

So, if you need to repair the rear wheel of a bicycle or it is just time to service the spare parts, you need to clarify the procedure to be carried out when removing a wheel.

READ  How To Remove A Camera From A Bicycle Wheel

Installing the rear wheel

The installation process is also similar to the installation of the front wheel, with a small exception: the chain must be seated correctly. To do this, bring the wheel to the attachment points, put the chain on the sprocket and then put the wheel in place. True, a situation may arise in which it will seem to you that the chain is perverted, and in order to unravel it, you will have to remove it. This is not true. You just need to twist it back and forth, imagine how it was installed on the stars before, and most importantly. don’t panic. That seems to be all. Now you have mastered the art of removing and installing wheels.

How to disassemble or reassemble the rear wheel of a speed bike

Removing the wheels from the frame is part of a mandatory bicycle maintenance procedure. Sooner or later, the wheel of even the most advanced bike will present surprises in the form of rim deformations, damaged spokes, burst tubes or even the entire tire, as well as wear of the sprocket system for the rear wheel.

Experienced cyclists welcome self-repair of wheels, and it is no coincidence: it is cheaper, and you will get some skills. You can also go to a good workshop, where the problem will be solved, perhaps faster, but not free of charge. Moreover, the service is hardly located under the windows of the house, so the bike will have to be dragged, which is not very pleasant. To avoid this, it is better to tinker a little yourself, especially since there is nothing complicated about the wheels. Today we’ll talk about how to remove the rear wheel from the bike, repair it and assemble it correctly.

# Spoiler # end_spoiler