DIY bike hanger

DIY bike hanger

bike, hanger

Awesome Garage Bike Rack/Storage. Build it for 20

In addition to the hanger, the made device also has the function of a shelf, so that you can put all your bike racks there.

According to the author, not so many materials and tools are needed to make this homemade product. A ready-made template is attached to the article, according to which you can cut out the necessary parts, and then you will only have to assemble the homemade product.

Materials and tools for making the hanger used by the author:

As for the tools, then here you need a very narrow assortment, but if you get by with the very minimum, then you should have a jigsaw, drill and sandpaper. Of course, a more professional solution would be to have a sander. electric jigsaw, stock up on a good number of clamps and so on.

List of materials:. plywood;. dowels;. glue for wood;. loops for attaching the hanger to the wall (metal plates);. self-tapping screws and other trifles.

Step one. Cutting out the first triangle First of all, you will need a printer, print on it the template that the author attached. If there is no printer, it is not scary, it is enough to arm yourself with a ruler and a pencil and you can easily draw the desired project. In addition, when making a template yourself, you can choose the required angles of the triangle so that the frame of your particular bike fits perfectly to it.

READ  How To Change A Tire On A Bicycle Rear Wheel

When the sheet with the drawing is, we glue it to the plywood, well, or cut it out of paper, and then circle it, as it is more convenient for someone. This figure will then need to be cut, the easiest way to do this is with a jigsaw.

DIY Bike Rack Wall Mount Rack Hanger | Wolangqueen Tv

Having cut out the first triangle, then you can cut out the next ones. As for the total quantity, then here it is already necessary to proceed from the thickness of the starting material. You need to achieve such a figure so that you can reliably hang your bike on it and there is a small margin left.

Step two. Drilling Holes The holes in the triangles serve two purposes. Firstly, thanks to them, the entire structure is assembled using dowels. And secondly, the holes allow all other triangles to be centered. Holes are drilled where they are marked on the template. It is not difficult to drill them, it can be done on a drilling machine, as well as with a hand or cordless drill.

When the holes are ready, the edges will have a lot of burrs. These defects must be eliminated, otherwise the triangles will not have to adhere properly to each other. It is easy to remove them, you can use ordinary sandpaper. advanced can use a power tool such as a grinder.

Cheap & Space Saving Bike Hanger On The Wall. Bike Storage DIY.

Step three. How did the author cut many triangles? If there are many triangles to be made, then manually making them all exactly the same will be problematic, and there will be a lot of work. For such purposes, the author used a fairly modern solution. a router. Such a device can use an already made triangle as source and accurately cut a copy of it.

READ  Spins the chain on the bike under load

However, you can also cut it by hand using a jigsaw. Then you just need to make some effort to make all the triangles the same by grinding. In any case, after cutting, you have to sand the edges to remove the burrs.

Step four. Assembly Using dowels and wood glue, we assemble the structure. Apply glue to each layer, insert the dowel and press down the triangle well. When you assemble the entire structure, it must be tightened with clamps in order to squeeze out excess glue and remove all possible gaps between the triangles. However, it is advisable to compress the entire structure as it is assembled, since the glue hardens rather quickly.

Step five. Veneer finishing This step is not necessary at all, it is just a matter of aesthetics. The author decided to decorate his brainchild with veneer. To do this, we take the necessary material and cut off another triangle, which will be the front part. Now the homemade product will look rich and at first glance no one will say that it is made of plywood.

If you use separate parts, that is, three boards, then they need to be cut to the desired length at the desired angle, and then glued. After gluing, the surface is sanded in one level. When the glue is dry, sand the veneer, make it flush with the main structure.

In order not to bother. You can just paint the front.

READ  How to adjust the reverse speed of your bike

In addition, in the middle of the hanger, you need to make a groove, thanks to which the bicycle frame will be securely fixed and will not slip. You can grind it using a router. But there are also manual methods, for example, the same sandpaper attached to a suitable object.

Step seven. Drill holes for mounting studs The entire structure must be securely fixed, as it must support the weight of the bike. In theory, the usual external hinges will be enough here, but it is best to drill holes in the attachment points and install long steel pins in them. The pins themselves will need to be glued, here you need good glue, it is better to use epoxy. On the other side of the pins there should be hinges, which are already attached to the structure to the wall.

Step eight. Final touches In the end, you can bring the surface to a perfectly smooth state and then polish with a polish, well, or use some other impregnation.

In addition, the author attaches a tape made of cork to the hanger, this will allow you to securely fix the bike, and also save the hanger from damage. The tape is very easy to attach using double-sided tape.